-
1 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
2 долгосрочный эксперимент
долгосрочный эксперимент
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
long-term experiment
1) Experiment lasting for a relatively long period of time. 2) Experiment whose results become effective after a long period of time. (Source: SHOOXa)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > долгосрочный эксперимент
-
3 долгосрочное прогнозирование
долгосрочное прогнозирование
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]
долгосрочное прогнозирование
Оценка будущего развития экономики, научно-технического прогресса, социальных изменений в обществе в долгосрочном периоде. В экономико-математических прогнозах эти стороны развития рассматриваются в единстве. Д.п. обычно относится к периоду в 10 - 15 лет, однако есть и так называемые сверхдолгосрочные прогнозы, или, правильнее, дальнесрочные, охватывающие существенно большие промежутки времени. Они, например, относятся к энергетике, градостроительству, лесному хозяйству, к состоянию природной среды. Как правило, подобные прогнозы существенно менее детализированы, чем кратко- и среднесрочные, в них шире применяются вероятностные оценки (см. Вероятность), а часто — и качественные суждения. Строятся научно-технические, социально-экономические и демографические прогнозы, каждый из которых объединяет и взаимоувязывает результаты многих частных прогнозов: развития тех или иных отраслей техники, производства товаров народного потребления, совершенствования экономического механизма и др. Основные методы прогнозирования в экономике, включая долгосрочное, приводятся в статье Прогнозирование.
[ http://slovar-lopatnikov.ru/]EN
long-term forecasting
The act or process of predicting and calculating the likely conditions or occurrences for an extended and future point in time, often involving the study and analysis of pertinent data. (Source: RHW / MHE)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > долгосрочное прогнозирование
-
4 расстояние утечки
расстояние утечки
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание. Стык между двумя элементами из изоляционного материала считают частью поверхности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
расстояние утечки (см. приложение В)
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание — При определении расстояния утечки относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9
[ ГОСТ Р 50345-99( МЭК 60898-95)]
расстояние утечки по поверхности
-
[IEV number 151-15-50]
путь утечки
Кратчайшее расстояние вдоль поверхности изоляции между двумя проводящими частями или между проводящей частью и доступной поверхностью.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - A joint between two pieces of insulating material is considered part of the surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - For the purpose of determining a creepage distance to accessible parts, the accessible surface of an insulating enclosure is considered conductive as if it was covered by a metal foil wherever it can be touched by a hand or a standard test finger according to figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
creepage distance
shortest distance along the surface of insulation between two conductive parts or between a conductive part and the accessible surface
[IEC 60335-1, ed. 4.0 (2001-05)]
creepage distance
shortest distance along the surface of a solid insulating material between two conductive parts
[IEV number 151-15-50]FR
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Un joint entre deux portions de matière isolante est considéré comme faisant partie de la surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Pour la détermination d'une ligne de fuite pour des parties accessibles, la surface accessible d'une enveloppe isolante est considérée comme conductrice comme si elle était recouverte d'une feuille métallique à tout endroit où elle peut être touchée par la main ou par le doigt d'essai normalisé conforme à la figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
ligne de fuite
plus petite distance le long de la surface de l’isolation entre deux parties conductrices ou entre une partie conductrice et la surface accessible
[IEC 60335-1, ed. 4.0 (2001-05)]
ligne de fuite, f
distance la plus courte, le long de la surface d'un isolant solide, entre deux parties conductrices
[IEV number 151-15-50]1) Должно быть проводящими
[Интент]Недопустимые, нерекомендуемые
Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > расстояние утечки
-
5 долгосрочная тенденция
долгосрочная тенденция
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
long-term trend
The prevailing tendency or general direction expected for some observed value over a lengthy and extended period of time, often determined by studying and analyzing statistical data. (Source: RHW / APD)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > долгосрочная тенденция
-
6 вырубка и сжигание леса как метод увеличения сельскохозяйственных площадей
вырубка и сжигание леса как метод увеличения сельскохозяйственных площадей
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
slash and burn culture
A traditional farming system that has been used by generations of farmers in tropical forests and the savannah of north and east Africa. It is known to be an ecologically sound form of cultivation, and because the soil is poor in tropical rain forests it is a sustainable method of farming. It is still practised today, primarily in the developing countries. Small areas of bush or forests are cleared and the smaller trees burned. This unlocks the nutrients in the vegetation and gives the soil fertilizer that is easily taken up by plants. A few years later the soil is degraded and the farmer moves on to do the same at another site. The original ground is left fallow for anything up to 20 years so that the forest can regenerate. With the growth in population and in the subsequent need for more farming land to produce food, the method is increasingly being used today to clear large areas of tropical forests for cattle ranching, and in most cases the ground is not left fallow for long enough and, with modern mechanized farming systems, not enough tree stumps or suitable habitats for plant life are left to start the regeneration process. (Source: WRIGHT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > вырубка и сжигание леса как метод увеличения сельскохозяйственных площадей
-
7 разрушение лесного покрова
разрушение лесного покрова
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
forest cover destruction
Destruction of forests is carried out in many countries in order to provide new land for agricultural or livestock purposes. It is often done without factors such as climate and topography having been sufficiently studied and on lands where slope nature of the soil or other physiographic characteristics clearly indicate that the land involved is suitable only for forest. Although these practices may lead to a temporary increase in productivity, there are also many indications that in the long run there is usually a decrease in productivity per unit of surface and that erosion and irreversible soil deterioration often accompany this process. Many factors contribute to forest cover destruction: timber production, clearance for agriculture, cutting for firewood and charcoal, fires, droughts, strip mining, pollution, urban development, population pressures, and warfare. (Source: WPR)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > разрушение лесного покрова
-
8 деградация природных ресурсов
деградация природных ресурсов
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
degradation of natural resources
The result of the cumulative activities of farmers, households, and industries, all trying to improve their socio-economic well being. These activities tend to be counterproductive for several reasons. People may not completely understand the long-term consequences of their activities on the natural resource base. The most important ways in which human activity is interfering with the global ecosystem are: a) fossil fuel burning which may double the atmospheric carbon dioxide concentration by the middle of the next century, as well as further increasing the emissions of sulphur and nitrogen very significantly; b) expanding agriculture and forestry and the associated use of fertilizers (nitrogen and phosphorous) are significantly altering the natural circulation of these nutrients; c) increased exploitation of the freshwater system both for irrigation in agriculture and industry and for waste disposal. (Source: WPR)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > деградация природных ресурсов
-
9 продолжительный режим коммутационного аппарата
непрерывный режим
длительный режим
-
[IEV number 442-05-43]EN
uninterrupted duty (for a switching device)
duty in which the main contacts of a switching device remain closed whilst carrying a steady current without interruption for long periods (which could be weeks, months, or even years)
[IEV number 442-05-43]FR
service ininterrompu (pour un dispositif de coupure)
service dans lequel les contacts principaux d'un dispositif de coupure restent fermés tout en transportant un courant permanent sans interruption pendant de longues périodes (qui peuvent être des semaines, des mois, et même des années)
[IEV number 442-05-43]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
Синонимы
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > продолжительный режим коммутационного аппарата
-
10 атмосферная инверсия
атмосферная инверсия
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
atmospheric inversion
A temperature inversion in the atmosphere in which the temperature, instead of falling, increases with height above the ground. With the colder and heavier air below, there is no tendency to form upward currents and turbulence is suppressed. Inversions are often formed in the late afternoon when the radiation emitted from the ground exceeds that received from the sinking sun. Inversions are also caused by katabatic winds, that is cold winds flowing down the hillside into a valley, and by anticyclones. In inversion layers, both vertical and horizontal diffusion is inhibited and pollutants become trapped, sometimes for long periods. Low-level discharges of pollutants are more readily trapped by inversions than high level dischargers, hence the case for high stacks. Furthermore, high level discharges into an inversion tend to remain at a high level because of the absence of vertical mixing. (Source: GILP96)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > атмосферная инверсия
-
11 воздействие рыболовства на окружающую среду
воздействие рыболовства на окружающую среду
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
environmental impact of fishing
Fishing may have various negative effects on the environment: effluent and waste from fish farms may damage wild fish, seals, and shellfish. Fish farmers use tiny quantities of highly toxic chemicals to kill lice: one overdose could be devastating. So-called by-catches, or the incidental taking of non-commercial species in drift nets, trawling operations and long line fishing is responsible for the death of large marine animals and one factor in the threatened extinction of some species. Some fishing techniques, like the drift nets, yield not only tons of fish but kill millions of birds, whales and seals and catch millions of fish not intended. Small net holes often capture juvenile fish who never have a chance to reproduce. Some forms of equipment destroy natural habitats, for example bottom trawling may destroy natural reefs. Other destructive techniques are illegal dynamite and cyanide fishing. (Source: WPR)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > воздействие рыболовства на окружающую среду
-
12 гигроскопичная лента
- Quellband, n
гигроскопичная лента
водонабухающая лента
лента, применяемая под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-16]EN
water blocking tape
swelling tape
tape applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-16]FR
ruban d'étanchéité
ruban gonflant
ruban appliqué sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-16]Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellband, n
FR
Русско-немецкий словарь нормативно-технической терминологии > гигроскопичная лента
-
13 гигроскопичная пудра
- Quellpulver, n
гигроскопичная пудра
водонабухающая пудра
порошковый наполнитель, применяемый под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-14]EN
water blocking powder
swelling powder
powder applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-14]FR
poudre d'étanchéité
poudre gonflante
poudre appliquée sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-14]Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellpulver, n
FR
Русско-немецкий словарь нормативно-технической терминологии > гигроскопичная пудра
-
14 гигроскопичный клей
- Quellmasse, f
гигроскопичный клей
водонабухающий клей
клей, применяемый под оболочкой или в промежутках между жилами кабеля или проволоками многопроволочной жилы кабеля для предотвращения протекания воды вдоль кабеля под оболочкой, например, при повреждении оболочки, или вдоль проводника жилы кабеля, например, при повреждении всех слоев покрытий кабеля вплоть до проводника
[IEV number 461-05-17]EN
water blocking glue
swelling glue
glue applied under a sheath or into the interstices of a conductor in order to prevent water migration along the cable
NOTE – Water migration can occur a) under the sheath, for example when the sheath has been damaged, or b) through the conductor, for example when cable layers through to the conductor have become damaged.
[IEV number 461-05-17]FR
matière d'étanchéité
matière appliquée sous une gaine ou dans les interstices d'une âme conductrice de façon à empêcher la propagation de l'eau le long du câble
NOTE – La propagation de l'eau peut avoir lieu a) sous la gaine, par exemple lorsque la gaine a été endommagée, ou b) à travers l'âme conductrice, par exemple lorsque les différentes couches constitutives du câble ont été endommagées jusqu'à l'âme conductrice.
[IEV number 461-05-17]
Тематики
- кабели, провода...
Синонимы
EN
DE
- Quellmasse, f
FR
Русско-немецкий словарь нормативно-технической терминологии > гигроскопичный клей
-
15 многостороннее соглашение
многостороннее соглашение
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
multilateral agreement
Multilateralism stands for a long-held but rarely achieved ideal, namely the voluntary co-operation of nations for peace and development. Multilateral initiatives are undermined or diluted by ultra-nationalist, bilateral and regional initiatives. Multilateralism may be undercut by the uncoordinated decisions of those contributing to it. Multilateralism constitutes the democracy of international society. An enlightened multilateralism enhances the specific interests of states while advancing their common cause. (Source: WPR)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > многостороннее соглашение
-
16 остаточное количество пестицидов
остаточное количество пестицидов
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
residual pesticide
A pesticide remaining in the environment for a fairly long time, continuing to be effective for days, weeks, and months. (Source: HMD)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > остаточное количество пестицидов
-
17 управление землями различного хозяйственного назначения
управление землями различного хозяйственного назначения
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
multiple use management area
1) Coordinated management for the most judicious and harmonious use of the land on a long term basis under the concept of combining two or more uses and/or purposes with attention to sustainability and nonimpairment of the natural resources and land area. 2) Use of land for more than one purpose; e.g. grazing of livestock, watershed and wildlife protection, recreation, and timber production. (Source: UNUN / EPAGLO)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > управление землями различного хозяйственного назначения
-
18 вал
m—FRA arbre m horizontalDEU Welle f für HandradITA albero m orizzontalePLN wałek m koła pokrętnegoRUS вал m маховикасм. поз. 563 на—FRA arbre m de manœuvre du déverseur escamotableDEU Welle f für Rutschenverlängerung fITA albero m di manovra dello scivoloPLN wałek m przedłużacza zsypuRUS вал m направляющей лоткасм. поз. 1406 на—FRA arbre m de manœuvre de la trappeDEU Welle f für RundschieberITA albero m di manovra della paratoiaPLN wał m napędowy klapy, pełnyRUS вал m привода люкасм. поз. 1399 навал привода люка, полый
—FRA arbre m creux de manœuvre de la trappeDEU Rohrwelle f für RundschieberITA albero m cavo di manovra della paratoiaPLN wał m napędowy klapy, drążonyRUS вал m привода люка, полыйсм. поз. 1398 навал привода переключателя тормозного режима
—FRA arbre m de commande de la boîte "Vide-Chargé"DEU Umstellwelle f für LastwechselITA albero m di comando del dispositivo "vuoto-carico"PLN wałek m zmieniacza hamownościRUS вал m привода переключателя тормозного режимасм. поз. 513 навал, гибкий
—FRA câble m de transmissionDEU Übertragungszug mITA cavo m di trasmissionePLN linka f napędowaRUS вал m, гибкийсм. поз. 2325 навал, гибкий, для привода вспомогательного оборудования
—FRA flexible m d’entraînement des auxiliairesDEU Antriebswelle f, biegsame, für HilfsmaschinenITA albero m flessibile di trasmissione agli apparecchi ausiliariPLN wałek m giętki napędu urządzeń pomocniczychRUS вал m, гибкий, для привода вспомогательного оборудованиясм. поз. 2481 на,
вал, запорный
—FRA arbre m de verrouillageDEU Verschlußwelle fENG locking barITA albero m del dispositivo di bloccaggioPLN wal m ryglowaniaRUS вал m, запорныйсм. поз. 1382 навал, карданный
—FRA arbre m à cardansDEU Gelenkwelle fENG cardan shaftITA albero m cardanicoPLN wał m kardanowyRUS вал m, карданныйсм. поз. 2034 навал, коленчатый
—FRA arbre m de verrouillageDEU Kniewelle fENG locking barITA albero m di bloccaggioPLN wał m zaciskowyRUS вал m, коленчатыйсм. поз. 961 навал, кулачковый
—FRA arbre m à crochetsDEU Hakenwelle fENG hook-barITA albero m con ganciPLN wał m pazurowyRUS вал m, кулачковыйсм. поз. 1389 навал, переводной
—FRA arbre m de commandeDEU Umstellwelle fENG control shaftITA albero m di comandoPLN wał m sterującyRUS вал m, переводнойсм. поз. 663 навал, сцепной
—FRA axe m d’entraînementDEU Mitnehmerbolzen mENG driving shaftITA perno m di trasmissionePLN wałek m napędzającyRUS вал m, сцепнойсм. поз. 2046 навал, тормозной
—FRA arbre m verticalDEU Bremswelle fENG vertical shaftITA albero m verticalePLN wał m przekładni zębatejRUS вал m, тормознойсм. поз. 566 на,FRA arbre mDEU Handbremswelle fENG brake shaftITA albero mPLN wał m dźwigni kątowejRUS вал m, тормознойсм. поз. 583 на,FRA arbre m du frein à levierDEU Bremswelle fENG brake shaftITA albero m del freno a stangaPLN wał m hamulcaRUS вал m, тормознойсм. поз. 598 навал, тормозной, длинный
—FRA arbre m de commande (côté opposé au cylindre)DEU Handbremswelle f, langeENG operating, shaft (long)ITA albero m di comando (lato opposto al cilindro)PLN wał m długi hamulcaRUS вал m, тормозной, длинныйсм. поз. 603 навал, тормозной, короткий
—FRA arbre m de commande (côté cylindre)DEU Handbremswelle f, kurzeITA albero m di comando (lato cilindro)PLN wał m krótki hamulcaRUS вал m, тормозной, короткийсм. поз. 602 навал, торсионный
—FRA barre f de torsionDEU Wiegenlenker m quer oder Torsionsstab mENG torsion barITA barra f di torsionePLN drążek m skrętnyRUS вал m, торсионныйсм. поз. 285 на -
19 антиводорослевый реагент
антиводорослевый реагент
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
antifouling agent
Agent that inhibits the growth of barnacles and other marine organisms on a ship's bottom (an antifouling paint or other coating). Organo-tin compounds have been the most often used agents in this application since they are effective against both soft and hard fouling organisms. However, in spite of their performance, they have a negative impact on the marine environment and their long half life in the environment, has prompted marine paint manufacturers to look for a nonpersistent alternative. (Source: CED / OLIN)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > антиводорослевый реагент
-
20 исчезающий вид
исчезающий вид
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
category of endangered species
Those of the planet's flora and fauna which are threatened with extinction. Hunting and poaching to fuel the trade in ivory, horn, skins, fur and feathers have long been a threat to already endangered species. Pollution, agricultural expansion, loss of wetlands, deforestation and other erosion of habitats have been added to the hazards. Human activity was responsible for most of the animals and plants known to have been lost in the past two centuries. (Source: WRIGHT)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > исчезающий вид
- 1
- 2
См. также в других словарях:
long for — verb a) To have a desire for; to yearn for; to crave for b) To miss someone See Also: longing, not long for … Wiktionary
Not Long for this World — Ja … Wikipedia
Everything I Long For — Infobox Album | Name = Everything I Long For Type = studio Artist = Hayden Recorded = February 1994 – January 1995 [http://www.geocities.com/SunsetStrip/Garage/4210/everything.htm Everything I Long For explained by Hayden] . Retrieved: 7 July… … Wikipedia
not long for this world — adjective unlikely to remain for much time Poor old Fred has cancer, and is not long for this world … Wiktionary
Long Day's Journey — Angel episode Episode no. Season 4 Episode 9 Directed by Terrence O Hara Written … Wikipedia
For You, For Me Tour — Tour by Kylie Minogue Start date September 30, 2009 End date … Wikipedia
For the Time Being — For the Time Being: A Christmas Oratorio, is a long poem by W. H. Auden, written 1941 42, and first published in 1944. It was one of two long poems included in Auden s book also titled For the Time Being , published in 1944; the other poem… … Wikipedia
long — I. adjective (longer; longest) Etymology: Middle English long, lang, from Old English; akin to Old High German lang long, Latin longus Date: before 12th century 1. a. extending for a considerable distance b. having greater length than usual < a… … New Collegiate Dictionary
Long rifle — Infobox Weapon|is ranged=yes caption=Kentucky Rilfe name=Kentucky Rifle type=Rifled musket origin=flagcountry|USA era= platform=Individual target=Personnel design date=c. 1700s production date= service=c.1730 c.1850 used by=USA wars= American… … Wikipedia
long — long1 longly, adv. longness, n. /lawng, long/, adj. longer /lawng geuhr, long /, longest /lawng gist, long /, n., adv. adj. 1. having considerable linear extent in space: a long distance; a long handle. 2. having considerable duration in time: a… … Universalium
Long's Regiment — Infobox Military Unit unit name=Long s Regiment caption= country= allegiance=Continental Congress of the United States type=Infantry branch= dates=1776 1777 specialization= command structure=New Hampshire Line size= current commander= garrison=… … Wikipedia