-
1 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
См. также в других словарях:
Cable television in the United States — is a common form of television delivery, generally by subscription. Cable television first became available in the United States in 1948, with subscription services in 1949. Data by SNL Kagan shows that as of 2006 about 58.4% of all American… … Wikipedia
Cable car (railway) — A cable car or cable railway is a mass transit system using rail cars that are propelled by a continuously moving cable running at a constant speed. Individual cars stop and start by releasing and gripping this cable as required. Cable cars are… … Wikipedia
Cable Internet — In telecommunications, cable Internet is a form of broadband Internet access that uses the cable television infrastructure. Like digital subscriber lines and fiber optic networks, cable Internet bridges the last kilometre or mile from the… … Wikipedia
Copper wire and cable — Copper has been used in electric wiring since the invention of the electromagnet and the telegraph in the 1820s.[1][2] The invention of the telephone in 1876 proved to be another early boon for copper wire.[3] Today, despite competition from… … Wikipedia
Submarine communications cable — A cross section of a submarine communications cable. 1 Polyethylene 2 Mylar tape 3 Stranded steel wires 4 Aluminium water barrier 5 Polycarbonate 6 Copper or aluminium tube 7 Petroleum jelly 8 Optical fib … Wikipedia
Power cable — This article is about electric power conductors. For portable equipment, see power cord. A power cable is an assembly of two or more electrical conductors, usually held together with an overall sheath. The assembly is used for transmission of… … Wikipedia
RNAL (cable system) — REACH North Asia Loop (RNAL) is a multi terabit intra Asia self healing submarine telecommunications cable system connecting the principal cities in Asia. The 10,000km cable network provides intra regional, city to city connectivity between Hong… … Wikipedia
SAT-3/WASC (cable system) — SAT 3/WASC or South Atlantic 3/West Africa Submarine Cable is a submarine communications cable linking Portugal and Spain to South Africa, with connections to several West African countries along the route. It forms part of the SAT 3/WASC/SAFE… … Wikipedia
Coaxial cable — RG 59 flexible coaxial cable composed of: A: outer plastic sheath B: woven copper shield C: inner dielectric insulator D: copper core Coaxial cable, or coax, has an inner conductor surrounded by a flexible, tubular insulating layer, surrounded by … Wikipedia
San Francisco cable car system — Infobox nrhp2 | name =San Francisco Cable Cars nhl=yes caption = Powell Hyde line cable car passing by Lombard Street in Russian Hill location= 1390 Washington Street, San Francisco, California [http://www.nr.nps.gov/writeups/66000233.nl.pdf NHL… … Wikipedia
Transatlantic telephone cable — A transatlantic telephone cable is a submarine communications cable that carries telephone traffic under the Atlantic Ocean.When the first transatlantic telegraph cable was laid in 1858 by businessman Cyrus West Field, it operated for only a… … Wikipedia
