-
1 длительный допустимый ток
- courant permanent admissible, m
- courant admissible, m
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-французский словарь нормативно-технической терминологии > длительный допустимый ток
-
2 корпус (счетчика энергии)
- boîtier (d'un compteur d’énergie)
корпус (счетчика энергии)
-
[IEV number 314-07-17]EN
case (of an energy meter)
set that comprises the base and the cover
[IEV number 314-07-17]FR
boîtier (d'un compteur d’énergie)
ensemble formé du socle et du couvercle
[IEV number 314-07-17]Тематики
- измерение электр. величин в целом
- счетчик электроэнергии
EN
DE
FR
- boîtier (d'un compteur d’énergie)
Русско-французский словарь нормативно-технической терминологии > корпус (счетчика энергии)
-
3 атмосферная инверсия
атмосферная инверсия
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
atmospheric inversion
A temperature inversion in the atmosphere in which the temperature, instead of falling, increases with height above the ground. With the colder and heavier air below, there is no tendency to form upward currents and turbulence is suppressed. Inversions are often formed in the late afternoon when the radiation emitted from the ground exceeds that received from the sinking sun. Inversions are also caused by katabatic winds, that is cold winds flowing down the hillside into a valley, and by anticyclones. In inversion layers, both vertical and horizontal diffusion is inhibited and pollutants become trapped, sometimes for long periods. Low-level discharges of pollutants are more readily trapped by inversions than high level dischargers, hence the case for high stacks. Furthermore, high level discharges into an inversion tend to remain at a high level because of the absence of vertical mixing. (Source: GILP96)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > атмосферная инверсия
-
4 гальваническая развязка
гальваническая развязка
Мероприятие или техническое средство, применение которого направлено на исключение гальванической связи между проводящими частями.
[РД-91.020.00-КТН-276-07]
гальваническая развязка
Схемотехническое решение, при котором исключается гальваническая связь между электрическими цепями. Гальваническая развязка осуществляется трансформаторами или оптоэлектронными приборами.
[Интент]EN
galvanic separation
prevention of electric conduction between two electric circuits intended to exchange power and/or signals
NOTE – Galvanic separation can be provided e.g. by an isolating transformer or an opto-coupler.
[IEV number 151-12-26]FR
séparation électrique, f
séparation galvanique (terme déconseillé), f
action ou moyen d’empêcher la conduction électrique entre deux circuits électriques prévus pour échanger de la puissance ou des signaux
NOTE – Une séparation électrique peut être obtenue, par exemple, au moyen d’un transformateur de séparation (de circuits) ou d’un optocoupleur.
[IEV number 151-12-26]Параллельные тексты EN-RU
Electrical isolation means that no current flow can occur from one electric circuit to a neighboring other electric circuit.
In case of power supplies, this means that no electric connection exists between the input side and the output side.
[ABB]Гальваническая развязка означает, что электрический ток не может протекать из какой-либо цепи в соседнюю цепь.
Для источников электропитания это означает, что не существует электрической связи между входной и выходной сторонами.
[Перевод Интент]The measured values are electrically isolated.
[Schneider Electric]Измеряемые величины гальванически развязаны от цепей устройства.
[Перевод Интент]Недопустимые, нерекомендуемые
Тематики
- электротехника, основные понятия
Близкие понятия
EN
DE
- galvanische Trennung
- Wellenimpedanz, (Leitungs-)
FR
Русско-французский словарь нормативно-технической терминологии > гальваническая развязка
-
5 переключающий контакт
переключающий контакт электрической цепи
Контакт электрической цепи, который размыкает одну электрическую цепь и замыкает другую при заданном действии устройства
[ ГОСТ 14312-79]
переключающий контакт
switching contact
Механический контакт, предназначенный для замыкания и размыкания электрической цепи.
[ ГОСТ Р МЭК 60050-426-2006]EN
change-over contact
combination of two contact circuits with three contact members, one of which is common to the two contact circuits; such that when one of these contact circuits is open, the other is closed
[IEV number 444-04-19]FR
contact à deux directions, m
contact inverseur (déconseillé), m
combinaison de deux circuits de contact comprenant trois éléments de contact, l'un d'eux étant commun aux deux circuits de contact ; de telle manière que lorsque l'un des circuits de contact est ouvert, l'autre est fermé
[IEV number 444-04-19]Параллельные тексты EN-RU CO contact
Compound contact consisting of a NO (make) contact and a NC (break) contact with a common terminal. On changing the switch position, the contact previously closed opens first followed by the closing of the contact that was previously open. Note: in case of a switching arc the NO and NC contact may be temporarily electrically connected.
[Tyco Electronics]Переключающий контакт
Контакт, объединяющий в себе замыкающий и размыкающий контакты с общим выводом. При изменении коммутационного положения сначала размыкается ранее замкнутый контакт, затем замыкается контакт, который до этого был разомкнут. Примечание. Если в процессе коммутации возникнет дуга между размыкающим и замыкающим контактами, то между ними может установиться кратковременная электрическая связь.
[Перевод Интент]Недопустимые, нерекомендуемые
Тематики
Обобщающие термины
Синонимы
EN
- C/O
- change-over contact
- changeover contact
- CO contact
- double-throw contact
- make-and-break contact
- switching contact
- transfer contact
- two-way contact
DE
FR
Русско-французский словарь нормативно-технической терминологии > переключающий контакт
-
6 проходной изолятор
- traversée
- isolateur de traversée, m
проходной изолятор
Изолятор, предназначенный для провода токоведущих элементов через стенку, имеющую другой электрический потенциал.
[ ГОСТ 27744-88]
проходной изолятор
-
[IEV number 151-15-40]EN
(insulating) bushing
insulator forming a passage for a conductor through a non-insulating partition
[IEV number 151-15-40]
bushing
A bushing is a cyclindrical insulating component, usually made of ceramic, that houses a conductor. It enables a conductor to pass through a grounded enclosure, such as a transformer tank (the physical shell of a transformer), a wall or other physical barrier, to connect electrical installations. In the case of a transformer, bushings protect the conductors that connect a transformer’s core to the power system it serves through channels in the transformer’s housing.
[ABB. Glossary of technical terms. 2010]FR
isolateur de traversée, m
traversée, f
isolateur permettant le passage d'un conducteur à travers une paroi non isolante
[IEV number 151-15-40]
Проходной изоляторПараллельные тексты EN-RU
The circuit breaker is connected via bushings to the rest of the switchgear at the flanges provided.
[Siemens]С другими частями распределительного устройства силовой выключатель соединяется через проходные изоляторы, закрепленные в его фланцах.
[Перевод Интент]Тематики
Классификация
>>>Обобщающие термины
EN
DE
FR
- isolateur de traversée, m
- traversée
Русско-французский словарь нормативно-технической терминологии > проходной изолятор
-
7 нефтесвязующее вещество
нефтесвязующее вещество
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
oil binding agent
Highly absorbent agents used for physically removing spilled oil in case of leakages and oil accidents occurring in water bodies, industry, work-shops, on roads, etc. Materials that have been found useful for this service vary from simple, naturally occurring materials such as straw, sawdust, and peat to synthetic agents, such as polyurethane foam and polystyrene powder. (Source: FUNKE / PZ)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > нефтесвязующее вещество
-
8 температура окружающей среды
- température ambiante, f
температура окружающей среды
Средняя температура воздуха или другой среды около оборудования.
Примечание - В процессе измерения температуры окружающей среды измерительный прибор (зонд) должен быть экранирован от сквозняков и нагрева излучением.
[ ГОСТ Р МЭК 60050-826-2009]
температура окружающей среды
Температура воздуха или другой среды в непосредственной близости от оборудования или компонента.
[ ГОСТ Р МЭК 60050-426-2006]
температура окружающей среды
Предполагают, что под температурой окружающей среды понимают воздействующие факторы со стороны всего другого оборудования, установленного в том же помещении.
Температура окружающей среды, которую следует учитывать применительно к оборудованию, - это температура в том месте, где оно должно быть установлено, с учетом влияния другого оборудования и источников тепла в том же месте в процессе работы без учета тепла от устанавливаемого оборудования
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]
температура окружающей среды
Температура воздуха или среды в том месте, где должно быть использовано оборудование.
[ ГОСТ Р МЭК 60204-1-2007]EN
ambient temperature
average temperature of air or another medium in the vicinity of the equipment
NOTE – During the measurement of the ambient temperature the measuring instrument/probe should be shielded from draughts and radiant heating.
[IEV number 826-10-03]
ambient temperature
temperature of the air or other medium where the equipment is to be used
[IEC 60204-1-2006]FR
température ambiante, f
température moyenne de l'air ou du milieu au voisinage du matériel
NOTE – Pendant la mesure de la température ambiante il est recommandé que l'instrument/la sonde de mesure soit protégée des courants d'air et de la chaleur rayonnée.
[IEV number 826-10-03]Параллельные тексты EN-RU
The temperate of each module of a Molded Case Circuit Breaker is the sum of temperature increase by conduction and ambient temperature and if the ambient temperature exceeds 40°C the passing current needs to be reduced so that the temperature of such element as internal insulator of MCCB exceed the maximum allowable temperature.
[LS Industrial Systems]Температура частей автоматического выключателя в литом корпусе равна температуре окружающей среды плюс температура, определяемая количеством теплоты, выделяемой при протекании электрического тока. Если автоматический выключатель эксплуатируется при температуре окружающей среды, превышающей 40 °C, то следует учитывать, что номинальный ток такого выключателя будет немного меньше. Учет этого обстоятельства позволит избежать недопустимого нагрева частей автоматического выключателя, выполненных из изоляционного материала.
[Перевод Интент]Тематики
EN
DE
- Umgebungstemperatur, f
FR
- température ambiante, f
Русско-французский словарь нормативно-технической терминологии > температура окружающей среды
См. также в других словарях:
in that case — Since that is the situation • • • Main Entry: ↑case * * * if that happens or has happened; if that is the situation I m free this evening. In that case, why not have dinner with me? * * * in that case : when that is considered : because of that… … Useful english dictionary
in that case — index consequently Burton s Legal Thesaurus. William C. Burton. 2006 … Law dictionary
in that case — because of that; that being so; since that is the reality of the situation … Idioms and examples
in that case — by this chance, in that situation, if so … English contemporary dictionary
Case-control — is a type of epidemiological study design. Case control studies are used to identify factors that may contribute to a medical condition by comparing subjects who have that condition (the cases ) with patients who do not have the condition but are … Wikipedia
Case Corporation — (formerly J.I. Case Company) was a manufacturer of construction and agricultural equipment. In 1999 it merged with New Holland to form CNH Global. The name Case lives on in two brands of the company: * Under the Case CE (for Construction… … Wikipedia
Case hardening — or surface hardening is the process of hardening the surface of a metal, often a low carbon steel, by infusing elements into the material s surface, forming a thin layer of a harder alloy. Case hardening is usually done after the part in question … Wikipedia
Case-based reasoning — (CBR), broadly construed, is the process of solving new problems based on the solutions of similar past problems. An auto mechanic who fixes an engine by recalling another car that exhibited similar symptoms is using case based reasoning. A… … Wikipedia
Case (rabbi) — Case was one of the foremost Polish rabbis and Talmudists of the end of the sixteenth century and the beginning of the seventeenth; died at Posen about 1610. His name, Case or Kaza is most probably only a variant of the well known surname Cases.… … Wikipedia
Case citation — Various case citations redirect here. If you are looking for the actual text of an opinion, it is usually linked in the external links at the bottom of the article on that case. For Wikipedia s template for case citation, see {{Template:Cite… … Wikipedia
Case study — This article is about the method of doing research. For the teaching method, see Case method. For the method of teaching law, see Casebook method. A case study is an intensive analysis of an individual unit (e.g., a person, group, or event)… … Wikipedia