-
1 расстояние утечки
расстояние утечки
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание. Стык между двумя элементами из изоляционного материала считают частью поверхности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
расстояние утечки (см. приложение В)
Кратчайшее расстояние по поверхности изоляционного материала между двумя токопроводящими1) частями.
Примечание — При определении расстояния утечки относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9
[ ГОСТ Р 50345-99( МЭК 60898-95)]
расстояние утечки по поверхности
-
[IEV number 151-15-50]
путь утечки
Кратчайшее расстояние вдоль поверхности изоляции между двумя проводящими частями или между проводящей частью и доступной поверхностью.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - A joint between two pieces of insulating material is considered part of the surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
creepage distance
shortest distance along the surface of an insulating material between two conductive parts
NOTE - For the purpose of determining a creepage distance to accessible parts, the accessible surface of an insulating enclosure is considered conductive as if it was covered by a metal foil wherever it can be touched by a hand or a standard test finger according to figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
creepage distance
shortest distance along the surface of insulation between two conductive parts or between a conductive part and the accessible surface
[IEC 60335-1, ed. 4.0 (2001-05)]
creepage distance
shortest distance along the surface of a solid insulating material between two conductive parts
[IEV number 151-15-50]FR
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Un joint entre deux portions de matière isolante est considéré comme faisant partie de la surface.
[IEC 60947-1, ed. 5.0 (2007-06)]
ligne de fuite
distance la plus courte le long de la surface d'une matière isolante entre deux parties conductrices
NOTE - Pour la détermination d'une ligne de fuite pour des parties accessibles, la surface accessible d'une enveloppe isolante est considérée comme conductrice comme si elle était recouverte d'une feuille métallique à tout endroit où elle peut être touchée par la main ou par le doigt d'essai normalisé conforme à la figure 9.
[IEC 60898-1, ed. 1.0 (2002-01)]
ligne de fuite
plus petite distance le long de la surface de l’isolation entre deux parties conductrices ou entre une partie conductrice et la surface accessible
[IEC 60335-1, ed. 4.0 (2001-05)]
ligne de fuite, f
distance la plus courte, le long de la surface d'un isolant solide, entre deux parties conductrices
[IEV number 151-15-50]1) Должно быть проводящими
[Интент]Недопустимые, нерекомендуемые
Тематики
- электротехника, основные понятия
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > расстояние утечки
-
2 воздушный зазор
- entrefer, m (2)
- distance d’isolement dans l’air
- distance d'isolement
воздушный зазор
Кратчайшее расстояние между двумя токоведущими и/или токоведущей и открытой проводящей частью.
МЭК 60050(441-17-31).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
воздушный зазор
Кратчайшее расстояние в воздухе между двумя токопроводящими1) частями вдоль линии наименьшей протяженности между этими токоведущими1) частями.
Примечание. Для определения воздушного зазора относительно доступных частей следует рассматривать доступную поверхность изоляционной оболочки как токопроводящую, как если бы она была покрыта металлической фольгой во всех местах, где ее можно коснуться рукой или стандартным испытательным пальцем в соответствии с рисунком 9.
(МЭС 441-17-31)
[ ГОСТ Р 50345-99( МЭК 60898-95)]
1) Должно быть проводящими
[Интент]
изоляционный промежуток
Расстояние между двумя токопроводящими частями вдоль нити, натянутой по кратчайшему пути между ними.
[ ГОСТ Р 52726-2007]
зазор
Кратчайшее расстояние по воздуху между двумя токопроводящими1) частями оборудования.
[ ГОСТ Р 52319-2005( МЭК 61010-1: 2001)]
1) Должно быть проводящими
[Интент]EN
clearance
the distance between two conductive parts along a string stretched the shortest way between these conductive parts
[IEV number 441-17-31]
clearance
shortest distance in air between two conductive parts
NOTE – This distance applies only to parts that are exposed to the atmosphere and not to parts which are insulated parts or covered with casting compound.
[IEV number 426-04-12]FR
distance d'isolement
distance entre deux parties conductrices le long d'un fil tendu suivant le plus court trajet possible entre ces deux parties conductrices
[IEV number 441-17-31]
distance d’isolement dans l’air
plus courte distance dans l’air entre deux pièces conductrices
NOTE – Cette distance s'applique seulement aux parties exposées à l'atmosphère et non aux parties isolées ou recouvertes par un composé de moulage.
[IEV number 426-04-12]
Параллельные тексты EN-RU
Clearance distance
Shortest distance in air between two conductive parts or between a conductive part and the accessible surface of the relay.
[Tyco Electronics]Воздушный зазор
Кратчайшее расстояние по воздуху между двумя проводящими частями или между проводящей частью и доступной для прикосновения поверхностью реле.
[Перевод Интент]
Наименьшее изоляционное расстояние по воздуху (в свету) от токоведущих до заземленных частей опоры
[ПУЭ]
2
воздушный зазор
-
[IEV number 151-14-05]EN
air gap
short gap in the magnetic material forming a magnetic circuit
Source: 221-04-13 MOD
[IEV number 151-14-05]FR
entrefer, m
coupure de faible longueur dans le matériau magnétique constituant un circuit magnétique
Source: 221-04-13 MOD
[IEV number 151-14-05]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
Синонимы
EN
- air clearance
- air distance
- air gap (2)
- air-gap clearance
- clearance
- contact gap (1)
- contact opening distance (1)
- contact separation (1)
- flashover distance
- insulation clearanse
- insulation distance
- isolating distance
DE
FR
- distance d'isolement
- distance d’isolement dans l’air
- entrefer, m (2)
Русско-французский словарь нормативно-технической терминологии > воздушный зазор
-
3 время дуги
время дуги
Время между моментами возникновения и окончательного погасания дуги.
[ ГОСТ Р 50339. 0-2003 ( МЭК 60269-1-98)]EN
arcing time
interval of time between the instant of the initiation of the arc and the instant of final arc extinction
[IEC 60127-1, ed. 2.0 (2006-06)]
arcing time
interval of time between the instant of the initiation of the arc between the arcing contacts and the instant of final arc extinction
[IEC 60077-3, ed. 1.0 (2001-12)]
arcing time
interval of time between the instant of the initiation of the arc in a fuse and the instant of final arc extinction in that fuse
[IEC 60077-5, ed. 1.0 (2003-07)]
arcing time
interval of time between the instant of the initiation of the arc in a pole or a fuse and the instant of final arc extinction in that pole or that fuse
[IEC 60282-2, ed. 3.0 (2008-04)]FR
durée d’arc
intervalle de temps entre l’instant du début de l’arc entre les contacts de coupure et l’instant de l’extinction finale de l’arc
[IEC 60077-3, ed. 1.0 (2001-12)]
durée d’arc
intervalle de temps entre l'instant de début de l'arc dans un fusible et l'instant de l'extinction finale de l'arc dans ce fusible
[IEC 60077-5, ed. 1.0 (2003-07)]
durée d’arc
intervalle de temps entre l’instant de début de l’arc sur un pôle ou sur un fusible et l’instant de l’extinction finale de l’arc sur ce pôle ou ce fusible
[IEC 60282-2, ed. 3.0 (2008-04)]Параллельные тексты EN-RU
Thanks to the new arcing chambers, the arc extinction time has been reduced, thereby guaranteeing high short-circuit current limitation.
[ABB]Благодаря применению новых дугогасительных камер уменьшено время дуги, вследствие чего гарантируется ограничение больших значений токов короткого замыкания.
[Перевод Интент]Тематики
- выключатель автоматический
- высоковольтный аппарат, оборудование...
- предохранитель
EN
FR
Русско-французский словарь нормативно-технической терминологии > время дуги
-
4 канал (тракт передачи измерительной информации)
канал
Индивидуальный тракт передачи измерительной информации в средстве измерений.
Примечание. "Канал" и "фаза" не одно и то же. Канал напряжения определяется разностью потенциалов между двумя проводниками. Понятие "фаза" относится к отдельному проводнику. В многофазных системах канал может быть между двумя фазами, или между фазой и нейтралью, или между фазой и землей, или между нейтралью и землей.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
channel
individual measurement path through an instrument
NOTE “Channel” and “phase” are not the same. A voltage channel is by definition the difference in potential between 2 conductors. Phase refers to a single conductor. On polyphase systems, a channel may be between 2 phases, or between a phase and neutral, or between a phase and earth, or between neutral and earth
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
voie (de mesure)
ensemble des dispositifs de mesure associés à une mesure individuelle
NOTE «Voies» et «phases» n’ont pas la même signification. Une voie de mesure correspond par définition à une différence de potentiel entre deux conducteurs. Une phase correspond à un simple conducteur. Dans les systèmes polyphasés, une voie de mesure peut être entre deux phases ou entre une phase et le neutre, ou entre une phase et la terre, ou entre le neutre et la terre.
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > канал (тракт передачи измерительной информации)
-
5 номинальное напряжение
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Русско-французский словарь нормативно-технической терминологии > номинальное напряжение
-
6 воздушный зазор между полюсами
воздушный зазор между полюсами
Воздушный зазор между любыми токопроводящими частями соседних полюсов.
МЭК 60050(441-17-32).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
clearance between poles
the clearance between any conductive parts of adjacent poles
[IEV number 441-17-32]FR
distance d'isolement entre pôles
distance d'isolement entre n'importe quelles parties conductrices de pôles adjacents
[IEV number 441-17-32]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
Синонимы
EN
DE
- Schlagweite/Luftstrecke zwischen den Polen
FR
Русско-французский словарь нормативно-технической терминологии > воздушный зазор между полюсами
-
7 нарушение условий конкуренции
нарушение условий конкуренции
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
distortion of competition
Article 85(1) of the EEC Treaty prohibits all agreements between undertakings, decisions by associations of undertakings and concerted practices which may affect trade between member states and which have as their object or effect the prevention, restriction or distortion of competition within the common market. All such arrangements are automatically null and void under Article 85(2), unless exempted by the Commission pursuant to Article 85(3). The text of Article 85 is as follows: "1. The following shall be prohibited as incompatible with the common market: all agreements between undertakings, decisions by associations of undertakings and concerted practices which may affect trade between member states and which have as their object or effect the prevention, restriction or distortion of competition within the common market, and in particular those which: (a) directly or indirectly fix purchase or selling prices or any other trading conditions; (b) limit or control production, markets, technical development, or investment; (c) share markets or sources of supply; (d) apply dissimilar conditions to equivalent transactions with other trading parties, thereby placing them at a competitive disadvantage; (e) make the conclusion of contracts subject to acceptance by the other parties of supplementary obligations which, by their nature or according to commercial usage, have no connection with the subject of such contracts. (Source: CLAORG)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > нарушение условий конкуренции
-
8 небаланс напряжений
небаланс напряжений
Отличие по модулю значения хотя бы одного из фазных или линейных напряжений многофазной системы электроснабжения от значений напряжений других фаз.
[ ГОСТ 23875-88]EN
voltage unbalance
phenomenon due to the differences between voltage deviations on the various phases, at a point of a polyphase system, resulting from differences between the phase currents or geometrical asymmetry in the line
[IEV number 604-01-29]
voltage unbalance (imbalance)
in a polyphase system, a condition in which the magnitudes of the phase voltages or the phase angles between consecutive phases are not all equal (fundamental component)
NOTE In three phase systems, the degree of inequality is usually expressed as the ratio of the negative and zero sequence components to the positive sequence component. In this technical report, voltage unbalance is considered in relation to three-phase systems and negative sequence only
[IEC 61000-3-13, ed. 1.0 (2008-02)]
voltage unbalance
condition in a polyphase system in which the r.m.s. values of the line voltages (fundamental component), and/or the phase angles between consecutive line voltages, are not all equal
NOTE 1 The degree of the inequality is usually expressed as the ratios of the negative- and zero-sequence components to the positive-sequence component.
NOTE 2 In this standard, voltage unbalance is considered in relation to 3-phase systems.
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
déséquilibre des tensions d'un réseau
phénomène résultant des différences de charge ou des dissymétries géométriques de lignes et qui provoque des différences entre les écarts de tension sur les diverses phases en un point d'un réseau polyphasé
[IEV number 604-01-29]
déséquilibre de tension
dans un réseau d’énergie électrique polyphasé, état dans lequel les valeurs efficaces des tensions entre conducteurs (composante fondamentale), et/ou les différences de phase entre conducteurs successifs, ne sont pas toutes égales
NOTE 1 Le taux de déséquilibre s’exprime habituellement par le rapport de la composante inverse ou homopolaire à la composante directe.
NOTE 2 Dans la présente norme, le déséquilibre de tension est relatif aux réseaux triphasés
[IEC 61000-4-30, ed. 2.0 (2008-10)]Параллельные тексты EN-RU
Voltage unbalance
Voltage unbalance on the most unbalanced phase, displayed as a percentage of Vavg.
[Schneider Electric]Небаланс напряжений
Самое значительное отличие по модулю значения одного из линейных напряжений, выраженное в процентах от среднего напряжения Vavg.
[Перевод Интент]
Недопустимые, нерекомендуемые
Тематики
EN
DE
FR
Смотри также
Русско-французский словарь нормативно-технической терминологии > небаланс напряжений
9 ограничение конкуренции
ограничение конкуренции
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
restriction on competition
Article 85(1) of the EEC Treaty prohibits all agreements between undertakings, decisions by associations of undertakings and concerted practices which may affect trade between member states and which have as their object or effect the prevention, restriction or distortion of competition within the common market. All such arrangements are automatically null and void under Article 85(2), unless exempted by the Commission pursuant to Article 85(3). The text of Article 85 is as follows: "1. The following shall be prohibited as incompatible with the common market: all agreements between undertakings, decisions by associations of undertakings and concerted practices which may affect trade between member states and which have as their object or effect the prevention, restriction or distortion of competition within the common market, and in particular those which: (a) directly or indirectly fix purchase or selling prices or any other trading conditions; (b) limit or control production, markets, technical development, or investment; (c) share markets or sources of supply; (d) apply dissimilar conditions to equivalent transactions with other trading parties, thereby placing them at a competitive disadvantage; (e) make the conclusion of contracts subject to acceptance by the other parties of supplementary obligations which, by their nature or according to commercial usage, have no connection with the subject of such contracts. (Source: CLAORG)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ограничение конкуренции
10 граница между воздухом и поверхностью океана
граница между воздухом и поверхностью океана
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
ocean-air interface
The sea and the atmosphere are fluids in contact with one another, but in different energy states - the liquid and the gaseous. The free surface boundary between them inhibits, but by no means totally prevents, exchange of mass and energy between the two. Almost all interchanges across this boundary occur most effectively when turbulent conditions prevail. A roughened sea surface, large differences in properties between the water and the air, or an unstable air column that facilitates the transport of air volumes from sea surface to high in the atmosphere. Both heat and water (vapor) tend to migrate across the boundary in the direction from sea to air. Heat is exchanged by three processes: radiation, conduction, and evaporation. The largest net exchange is through evaporation, the process of transferring water from sea to air by vaporization of the water. (Source: PARCOR)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > граница между воздухом и поверхностью океана
11 изоляционный промежуток между разомкнутыми контактами
изоляционный промежуток между разомкнутыми контактами
Суммарный промежуток между контактами или любыми присоединенными к ним токопроводящими частями полюса контактного коммутационного аппарата в отключенном состоянии
[ ГОСТ Р 52726-2007]
воздушный зазор между разомкнутыми контактами (раствор)
Полный воздушный зазор между контактами или любыми токопроводящими частями, соединенными с контактами полюса контактного коммутационного аппарата в разомкнутом положении.
МЭК 60050(441-17-34).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
clearance between open contacts
the total clearance between the contacts, or any conductive parts connected thereto, of a pole of a mechanical switching device in the open position
[IEV number 441-17-34]FR
distance d'isolement entre contacts ouverts
Параллельные тексты EN-RU
distance d'isolement totale entre les contacts, ou n'importe quelles parties conductrices qui leur sont reliées, d'un pôle d'un appareil mécanique de connexion dans la position d'ouverture
[IEV number 441-17-34]When the supply disconnecting device is one of the types specified in 5.3.2 a) to d) it shall fulfil all of the following requirements:
– have a visible contact gap or a position indicator which cannot indicate OFF (isolated) until all contacts are actually open and the requirements for the isolating function have been satisfied;
...
[IEC 60204-1-2006]Аппараты отключения электропитания, указанные в п. 5.3.2, в перечислениях а)...d), должны удовлетворять всем перечисленным ниже требованиям:
- иметь видимый изоляционный промежуток между разомкнутыми контактами или указатель коммутационного положения, который указывает на положение ОТКЛЮЧЕНО (отделено) только в том случае, если все контакты аппарата разомкнуты и все остальные требования, относящиеся к функции разъединения, выполнены;
...
[Перевод Интент]Тематики
- аппарат, изделие, устройство...
- выключатель автоматический
- выключатель, переключатель
- высоковольтный аппарат, оборудование...
Синонимы
EN
- clearance between open contacts
- contact gap
- contact opening distance
- contact separation
- flashover distance across the open circuit-breaker
DE
FR
Русско-французский словарь нормативно-технической терминологии > изоляционный промежуток между разомкнутыми контактами
12 короткое замыкание
короткое замыкание
Случайное или намеренное соединение резистором или импедансом со сравнительно низким сопротивлением двух или более точек в цепи, нормально находящихся под различным напряжением.
Случайное или намеренное низкоимпедансное или низкоомное соединение двух или более точек электрической цепи, нормально находящихся под разными электрическими потенциалами. (вариант компании Интент)
МЭК 60050(151-03-41) [2].
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
короткое замыкание
Случайный или преднамеренный проводящий путь между двумя или более проводящими частями, принуждающий различия электрических потенциалов между этими проводящими частями становиться равными или близкими к нулю.
Короткое замыкание обычно возникает в аварийном режиме электроустановки здания при повреждении изоляции токоведущих частей, находящихся под разными электрическими потенциалами, и возникновении между этими частями электрического контакта, имеющего пренебрежимо малое полное сопротивление. Короткое замыкание также может быть следствием ошибочных действий, совершаемых персоналом при монтаже и эксплуатации электроустановки здания, когда соединяют между собой проводящие части, которые в нормальном режиме находятся под разными электрическими потенциалами.
Короткое замыкание характеризуется током короткого замыкания, который, многократно превышая номинальный ток электрической цепи, может вызвать возгорание её элементов и явиться причиной пожара в здании. Поэтому в электроустановках зданий всегда проводят мероприятия, направленные на снижение вероятности возникновения короткого замыкания, а также выполняют защиту от короткого замыкания с помощью устройств защиты от сверхтока.
[ http://www.volt-m.ru/glossary/letter/%CA/view/27/]
короткое замыкание
Случайное или преднамеренное соединение двух или более проводящих частей, вызывающее снижение разности электрических потенциалов между этими частями до нуля или значения, близкого к нулю.
[ ГОСТ Р МЭК 60050-195-2005]
короткое замыкание
КЗ
замыкание, при котором токи в ветвях электроустановки, примыкающих к месту его возникновения, резко возрастают, превышая наибольший допустимый ток продолжительного режима
[Методические указания по защите распределительных электрических сетей напряжением 0,4-10 кВ от грозовых перенапряжений]EN
short-circuit
accidental or intentional conductive path between two or more conductive parts forcing the electric potential differences between these conductive parts to be equal to or close to zero
Source: 151-03-41 MOD
[IEV number 195-04-11]FR
court-circuit
chemin conducteur accidentel ou intentionnel entre deux ou plusieurs parties conductrices forçant les différences de potentiel électriques entre ces parties conductrices à être nulles ou proches de zéro
Source: 151-03-41 MOD
[IEV number 195-04-11]Параллельные тексты EN-RU
A short-circuit is a low impedance connection between two conductors at different voltages.
[ABB]Короткое замыкание представляет собой низкоомное соединение двух проводников, находящихся под разными потенциалами.
[Перевод Интент]Тематики
- электробезопасность
- электротехника, основные понятия
Синонимы
- КЗ
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > короткое замыкание
13 однородное поле
однородное поле
Электрическое поле с практически постоянным градиентом напряжения между электродами как между двумя сферами, радиус каждой из которых больше расстояния между ними.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
homogeneous (uniform) field
electric field which has an essentially constant voltage gradient between electrodes, such as that between two spheres where the radius of each sphere is greater than the distance between them
[IEC 60947-1, ed. 5.0 (2007-06)]FR
champ homogène (uniforme)
champ électrique dont le gradient de tension est essentiellement constant entre les électrodes, comme c'est le cas entre deux sphères où le rayon de chacune est plus grand que la distance qui les sépare
[IEC 60947-1, ed. 5.0 (2007-06)]Тематики
- электротехника, основные понятия
EN
FR
Русско-французский словарь нормативно-технической терминологии > однородное поле
14 полное сопротивление относительно земли
полное сопротивление относительно земли
Полное сопротивление (импеданс) между точкой системы или установки, или оборудования и относительной землей на данной частоте.
[ ГОСТ Р МЭК 60050-195-2005]
полное сопротивление относительно земли
Полное сопротивление между определенной точкой системы или установки, или оборудования и эталонной землей на данной частоте.
[ ГОСТ Р МЭК 60050-826-2009]EN
impedance to earth
impedance at a given frequency between a specified point in a system or in an installation or in equipment and reference earth
[IEV number 195-01-17]
impedance to earth
impedance to ground (US)
impedance at a given frequency between a specified point in a system or in an installation or in equipment and reference earth
NOTE 1 – Reference earth is defined in IEC 60050-195. In practice, a reference point can be substituted to earth, for example the chassis.
NOTE 2 – The common mode rejection ratio of an instrument is dependent on the impedances between the input terminals and earth. Each of these impedances is called a common mode impedance.
Source: 195-01-17
[IEV number 312-06-20]FR
impédance de mise à la terre
impédance à une fréquence donnée entre un point spécifié d'un réseau, d'une installation ou d'un matériel et la terre de référence
[IEV number 195-01-17]
impédance de mise à la terre
impédance à une fréquence donnée entre un point spécifié d'un réseau, d'une installation ou d'un matériel et la terre de référence
NOTE 1 – La terre de référence est définie dans la CEI 60050-195. En pratique, on peut lui substituer un point de référence, par exemple la masse.
NOTE 2 – Le facteur de réjection de mode commun d'un appareil dépend de l'impédance entre chacune des bornes d'entrée et la terre. Chacune de ces impédances est appelée impédance de mode commun.
Source: 195-01-17
[IEV number 312-06-20]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > полное сопротивление относительно земли
15 разделитель
разделитель
Тонкий слой, выполняющий роль барьера, предупреждающего взаимное вредное воздействие различных компонентов кабеля друг на друга таких, как токопроводящая жила и изоляция или изоляция и оболочка.
[IEV number 461-05-01]EN
separator
thin layer used as a barrier to prevent mutually detrimental effects between different components of a cable, such as between the conductor and insulation or between insulation and sheath
[IEV number 461-05-01]FR
séparateur
couche mince utilisée comme barrière pour éviter les interactions nocives entre deux constituants d'un câble, par exemple entre âme et enveloppe isolante ou entre enveloppe et gaine
[IEV number 461-05-01]Тематики
- кабели, провода...
EN
DE
- Trennschicht (eines Kabels), f
FR
Русско-французский словарь нормативно-технической терминологии > разделитель
16 безопасное сверхнизкое напряжение
безопасное сверхнизкое напряжение
Напряжение, не превышающее 42 В между проводниками и между проводниками и землей; при этом напряжение холостого хода не превышает 50 В. Если безопасное сверхнизкое напряжение получают от сети питания, оно должно поступать через безопасный разделительный трансформатор или преобразователь с раздельными обмотками, изоляция которых соответствует требованиям к двойной или усиленной изоляции.
Примечания.
- Установленные предельные значения напряжений основаны на предположении, что безопасный разделительный трансформатор работает при своем номинальном напряжении.
- Безопасный разделительный трансформатор 1) известен также как SELV.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
1) Должно быть безопасное сверхнизкое напряжение
[Интент]
безопасное сверхнизкое напряжение
Напряжение в цепи, электрически отделенной от питающей сети безопасным разделительным трансформатором, не превышающее 50 В переменного тока или 50√2 В пульсирующего постоянного тока между проводниками или между любым проводником и землей
[ ГОСТ 30030-93]safety extra-low voltage
voltage not exceeding 42 V between conductors and between conductors and earth, the no-load voltage not exceeding 50 V
When safety extra-low voltage is obtained from the supply mains, it is to be through a safety isolating transformer or a convertor with separate windings, the insulation of which complies with double insulation or reinforced insulation requirements.
NOTE 1 - The voltage limits specified are based on the assumption that the safety isolating transformer is supplied at its rated voltage.
NOTE 2 - Safety extra-low voltage is also known as SELV.
[IEC 60335-1, ed. 4.0 (2001-05)]FR
très basse tension de sécurité
tension ne dépassant pas 42 V entre conducteurs et entre conducteurs et terre, la tension à vide ne dépassant pas 50 V.
Si une très basse tension de sécurité est obtenue à partir du réseau d’alimentation, elle doit être fournie par l'intermédiaire d'un transformateur de sécurité ou d'un convertisseur à enroulements séparés, dont l'isolation répond aux prescriptions de la double isolation ou de l'isolation renforcée.
NOTE 1 - Les limites prescrites pour la tension sont établies en supposant que le transformateur de sécurité est alimenté sous sa tension assignée.
NOTE 2 - La très basse tension de sécurité est également appelée TBTS.
[IEC 60335-1, ed. 4.0 (2001-05)]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > безопасное сверхнизкое напряжение
17 биоразнообразие
биоразнообразие
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
biodiversity
1) Genetic diversity: the variation between individuals and between populations within a species; species diversity: the different types of plants, animals and other life forms within a region; community or ecosystem diversity: the variety of habitats found within an area (grassland, marsh, and woodland for instance. 2) An umbrella term to describe collectively the variety and variability of nature. It encompasses three basic levels of organisation in living systems: the genetic, species, and ecosystem levels. Plant and animal species are the most commonly recognized units of biological diversity, thus public concern has been mainly devoted to conserving species diversity. (Source: WRES / GILP96)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > биоразнообразие
18 боковая поверхность
боковая поверхность
Участок, образующийся между внутренней и наружной поверхностями
[ ГОСТ 28500-90( ИСО 5288-82)]EN
flank
Area defined by the width of the belt and the straight portion of the tooth section contained between the tip line and the root line
[ ГОСТ 28500-90( ИСО 5288-82)]FR
flanc
Surface définie par la largeur de la courroie et la partie rectiligne de la dent comprise entre la ligne de tête et la ligne de pied
[ ГОСТ 28500-90( ИСО 5288-82)]боковая поверхность
Одна из поверхностей, ограниченных шириной шкива и верхней и нижней поверхностями цилиндра (или прямолинейными участками)
[ ГОСТ 28500-90( ИСО 5288-82)]EN
flank
Area defined by the width of the pulley and the involute (or straight) portion of a pulley tooth contained between the tip cylinder and the root cylinder
[ ГОСТ 28500-90( ИСО 5288-82)]FR
flanc
Une des surfaces définies par la largeur de la poulie et par la partie en développante de cercle (ou rectiligne) de la dent qui est comprise entre le cylinder de tête et le cylindre de pied
[ ГОСТ 28500-90( ИСО 5288-82)]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > боковая поверхность
19 внешний проводник
внешний проводник
-
[IEV number 442-01-37]
внешний провод
Любой кабель, гибкий шнур, токопроводящая жила или провод, часть которого выступает наружу из управляющего устройства, встроенного в шнур, из управляющего устройства с независимым монтажом или из оборудования, в (или на) котором установлено управляющее устройство.
Примечание - Такой провод может быть либо питающим, либо функциональным, либо промежуточным шнуром между различными частями оборудования, либо может быть частью стационарной электропроводки.
[ГОСТ IЕС 60730-1-2011]EN
external conductor
any cable, flexible cable or cord, core or conductor, a part of which is external to an accessory
NOTE – Such a conductor can be a supply lead or interconnecting cord between separate parts of an accessory; it can form part of the fixed wiring.
[IEV number 442-01-37]
external conductor
any cable, flexible cord, core or conductor, a part of which is external to an inline cord control, an independently mounted control or to an equipment in or on which a control is mounted
Note 1 to entry: Such a conductor may be a supply lead, a function cord or interconnecting cord between different parts of an equipment; or it may form part of the fixed wiring.
[IEC 60730-1, ed. 5.0 (2013-11)]FR
conducteur externe
tout câble souple, âme conductrice ou conducteur dont une partie est extérieure à l'appareil
NOTE – Un tel conducteur peut-être un câble d'alimentation ou un cordon de raccordement entre des parties séparées d'un appareil ou encore constituer une partie du câblage fixe.
[IEV number 442-01-37]
conducteur externe
câble souple, cordon, âme conductrice ou conducteur dont une partie sort d'un dispositif de commande intercalé, d'un dispositif de commande à montage indépendant ou d'un matériel dans ou sur lequel un dispositif de commande est monté
Note 1 à l'article: Un tel conducteur peut soit être un câble d'alimentation, un câble fonctionnel ou un cordon de raccordement entre différentes parties d'un appareil, soit constituer une partie du câblage fixe d'un matériel.
[IEC 60730-1, ed. 5.0 (2013-11)]Тематики
- электротехника, основные понятия
Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > внешний проводник
20 время устойчивого замыкания (размыкания) контакта электрического реле
- Temps de fermeture (d’ouverture) stable
- temps de fermeture (d'ouverture) stable
время устойчивого замыкания (размыкания) контакта электрического реле
Интервал времени от момента достижения входной воздействующей величины электрического реле определенного значения до момента, когда цепь контакта электрического реле замкнется (разомкнется)
[ ГОСТ 16022-83]EN
time to stable closed condition
the time interval between the instant when a specified value of the input energizing quantity is applied and the instant when a contact is closed and fulfils specified requirements
[IEV number 446-17-24]
time to stable open condition
the time interval between the instant when a specified value of the input energizing quantity is applied and the instant when a contact is open and fulfils specified requirements
[IEV number 446-17-25]FR
temps de fermeture stable
temps écoulé entre l'instant d'application d'une valeur spécifiée de la grandeur d'alimentation d'entrée et l'instant où un circuit de contact est fermé et répond aux prescriptions spécifiées
[IEV number 446-17-24]
temps d'ouverture stable
temps écoulé entre l'instant d'application d'une valeur spécifiée de la grandeur d'alimentation d'entrée et l'instant où un circuit de contact est ouvert et répond aux prescriptions spécifiées
[IEV number 446-17-25]
Тематики
EN
DE
FR
136. Время устойчивого замыкания (размыкания) контакта электрического реле
D. Ansprech-Rückfallzeit
Е. Time to stable closed (open) condition
F. Temps de fermeture (d’ouverture) stable
Интервал времени от момента достижения входной воздействующей величины электрического реле определенного значения до момента, когда цепь контакта электрического реле замкнется (разомкнется)
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > время устойчивого замыкания (размыкания) контакта электрического реле
См. также в других словарях:
between — 1. general. Between is an adverb (houses with spaces between) and a preposition (houses with spaces between them). We are concerned here with between as a preposition. 2. between and among. Many people, and usage guides, cling to the idea… … Modern English usage
Between — Be*tween , prep. [OE. bytwene, bitweonen, AS. betwe[ o]nan, betwe[ o]num; prefix be by + a form fr. AS. tw[=a] two, akin to Goth. tweihnai two apiece. See {Twain}, and cf. {Atween}, {Betwixt}.] 1. In the space which separates; betwixt; as, New… … The Collaborative International Dictionary of English
Between decks — Between Be*tween , prep. [OE. bytwene, bitweonen, AS. betwe[ o]nan, betwe[ o]num; prefix be by + a form fr. AS. tw[=a] two, akin to Goth. tweihnai two apiece. See {Twain}, and cf. {Atween}, {Betwixt}.] 1. In the space which separates; betwixt; as … The Collaborative International Dictionary of English
Between ourselves — Between Be*tween , prep. [OE. bytwene, bitweonen, AS. betwe[ o]nan, betwe[ o]num; prefix be by + a form fr. AS. tw[=a] two, akin to Goth. tweihnai two apiece. See {Twain}, and cf. {Atween}, {Betwixt}.] 1. In the space which separates; betwixt; as … The Collaborative International Dictionary of English
Between themselves — Between Be*tween , prep. [OE. bytwene, bitweonen, AS. betwe[ o]nan, betwe[ o]num; prefix be by + a form fr. AS. tw[=a] two, akin to Goth. tweihnai two apiece. See {Twain}, and cf. {Atween}, {Betwixt}.] 1. In the space which separates; betwixt; as … The Collaborative International Dictionary of English
Between you and me — Between Be*tween , prep. [OE. bytwene, bitweonen, AS. betwe[ o]nan, betwe[ o]num; prefix be by + a form fr. AS. tw[=a] two, akin to Goth. tweihnai two apiece. See {Twain}, and cf. {Atween}, {Betwixt}.] 1. In the space which separates; betwixt; as … The Collaborative International Dictionary of English
Between the Lions — logo Format Children s television series Puppet Created by Lou Berge … Wikipedia
Between the Buttons — Studio album by The Rolling Stones Released 20 January 1967 (UK) 11 Februa … Wikipedia
between — [bē twēn′, bitwēn′] prep. [ME bitwene < OE betweonum < be,BY + tweonum (dat. of * tweon); akin to Goth tweihnai, by twos, in pairs: for IE base see TWO] 1. in or through the space that separates (two things) [between the house and the… … English World dictionary
Between (Pern) — Between in Anne McCaffrey s Dragonriders of Pern series is a dimension through which dragons and fire lizards travel during the process of teleportation, referred to as going between . If the dragon does not have a clear picture of its… … Wikipedia
Between the Devil and the Deep Blue Sea — is an idiom meaning a dilemma i.e., to choose between two undesirable situations (equivalent to between a rock and a hard place ). Its original meaning may be that of a nautical reference citing the deep blue sea and a devil a seam (where two… … Wikipedia
Перевод: с русского на французский
с французского на русский- С французского на:
- Русский
- С русского на:
- Все языки
- Английский
- Итальянский
- Немецкий
- Персидский
- Французский
- Эстонский