-
1 cooling area
<tech.gen> ■ Kühlfläche f -
2 water
* -
3 sprinkler
< comvhcl> ■ Sprengwagen m -
4 длительный допустимый ток
- Strombelastbarkeit, f
- Dauerstrombelastbarkeit, f
(длительный) допустимый ток
Максимальное значение электрического тока, который может протекать длительно по проводнику, устройству или аппарату при определенных условиях без превышения определенного значения их температуры в установившемся режиме
[ ГОСТ Р МЭК 60050-826-2009]
Этот ток обозначают IZ
[ ГОСТ Р 50571. 1-2009 ( МЭК 60364-1: 2005)]EN
(continuous) current-carrying capacity
ampacity (US)
maximum value of electric current which can be carried continuously by a conductor, a device or an apparatus, under specified conditions without its steady-state temperature exceeding a specified value
[IEV number 826-11-13]
ampacity
The current in amperes that a conductor can carry continuously under the conditions of use without exceeding its temperature rating.
[National Electrical Cod]FR
courant (permanent) admissible, m
valeur maximale du courant électrique qui peut parcourir en permanence, un conducteur, un dispositif ou un appareil, sans que sa température de régime permanent, dans des conditions données, soit supérieure à la valeur spécifiée
[IEV number 826-11-13]Ampacity, the term is defined as the maximum amount of current a cable can carry before sustaining immediate or progressive deterioration. Also described as current rating or current-carrying capacity, is the RMS electric current which a device can continuously carry while remaining within its temperature rating. The ampacity of a cable depends on:
- its insulation temperature rating;
- conductor electrical properties for current;
- frequency, in the case of alternating currents;
- ability to dissipate heat, which depends on cable geometry and its surroundings;
- ambient temperature.
Electric wires have some resistance, and electric current flowing through them causes voltage drop and power dissipation, which heats the cable. Copper or aluminum can conduct a large amount of current before melting, but long before the conductors melt, their insulation would be damaged by the heat.
The ampacity for a power cable is thus based on physical and electrical properties of the material & construction of the conductor and of its insulation, ambient temperature, and environmental conditions adjacent to the cable. Having a large overall surface area may dissipate heat well if the environment can absorb the heat.
In a long run of cable, different conditions govern, and installation regulations normally specify that the most severe condition along the run governs the cable's rating. Cables run in wet or oily locations may carry a lower temperature rating than in a dry installation. Derating is necessary for multiple circuits in close proximity. When multiple cables are near, each contributes heat to the others and diminishes the amount of cooling air that can flow past the individual cables. The overall ampacity of the insulated conductors in a bundle of more than 3 must be derated, whether in a raceway or cable. Usually the de-rating factor is tabulated in a nation's wiring regulations.
Depending on the type of insulating material, common maximum allowable temperatures at the surface of the conductor are 60, 75 and 90 degrees Celsius, often with an ambient air temperature of 30°C. In the U.S., 105°C is allowed with ambient of 40°C, for larger power cables, especially those operating at more than 2 kV. Likewise, specific insulations are rated 150, 200 or 250°C.
The allowed current in cables generally needs to be decreased (derated) when the cable is covered with fireproofing material.
For example, the United States National Electric Code, Table 310-16, specifies that up to three 8 AWG copper wires having a common insulating material (THWN) in a raceway, cable, or direct burial has an ampacity of 50 A when the ambient air is 30°C, the conductor surface temperature allowed to be 75°C. A single insulated conductor in air has 70 A rating.
Ampacity rating is normally for continuous current, and short periods of overcurrent occur without harm in most cabling systems. The acceptable magnitude and duration of overcurrent is a more complex topic than ampacity.
When designing an electrical system, one will normally need to know the current rating for the following:- Wires
- Printed Circuit Board traces, where included
- Fuses
- Circuit breakers
- All or nearly all components used
Some devices are limited by power rating, and when this power rating occurs below their current limit, it is not necessary to know the current limit to design a system. A common example of this is lightbulb holders.
[http://en.wikipedia.org/wiki/Ampacity]
Тематики
- электротехника, основные понятия
Синонимы
EN
DE
- Dauerstrombelastbarkeit, f
- Strombelastbarkeit, f
FR
- courant admissible, m
- courant permanent admissible, m
Русско-немецкий словарь нормативно-технической терминологии > длительный допустимый ток
-
5 приток воды
приток воды
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
inflow
1) Water other than wastewater that enters a sewer system (including sewer service connections) from sources such as, but not limited to, roof leaders, cellars drains, yard drains, area drains, drains from springs and swampy areas, manhole covers, cross connections between storm sewers and sanitary sewers, catch basins, cooling towers, storm waters, surface runoff, street wash waters, or drainage. Inflow does not include, and is distinguished from, infiltration. 2) Action of flowing in; an inflow of effluent into a river. (Source: JJK / PHC)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-немецкий словарь нормативно-технической терминологии > приток воды
См. также в других словарях:
cooling area — aušinimo plotas statusas T sritis fizika atitikmenys: angl. cooling area vok. Kühlfläche, f rus. площадь охлаждения, f pranc. aire de refroidissement, f … Fizikos terminų žodynas
Cooling tower — Natural draft wet cooling hyperboloid towers at Didcot Power Station, UK … Wikipedia
Cooling load temperature difference calculation method — Contents 1 CLTD/CLF/SCL Cooling Load Calculation Method 2 History 3 Application 4 Explanation of Variables … Wikipedia
cooling system — Apparatus used to keep the temperature of a structure or device from exceeding limits imposed by needs of safety and efficiency. In a mechanical transmission, the oil loses its lubricating capacity if overheated; in a hydraulic coupling or… … Universalium
cooling fins — The fins around the cylinder head of a reciprocating engine, which improve the normal cooling action. The fins increase the area of the cylinder and thus provide for greater heat transfer … Aviation dictionary
cooling fins — The greater the surface area that needs to be cooled, the better you will be able to cool off a hot object, like an engine. By putting a number of fins on a surface, you increase the overall area. On air cooled engines, for instance, you will see … Dictionary of automotive terms
cooling tower — /ˈkulɪŋ taʊə/ (say koohling towuh) noun a concrete or wooden structure used in industrial processes to cool water after it has passed through a condenser; so arranged that the maximum surface area of water is exposed to the atmosphere …
Engine cooling — is cooling an engine, typically using either air or liquid.OverviewHeat engines generate mechanical power by extracting energy from heat flows, much as a water wheel extracts mechanical power from a flow of mass falling through a distance.… … Wikipedia
Water cooling — Cooling tower and water discharge of a nuclear power plant Water cooling is a method of heat removal from components and industrial equipment. As opposed to air cooling, water is used as the heat conductor. Water cooling is commonly used for… … Wikipedia
Computer cooling — An OEM AMD heatsink mounted onto a motherboard. Computer cooling is required to remove the waste heat produced by computer components, to keep components within their safe operating temperature limits. Various cooling methods help to improve… … Wikipedia
Cortical cooling — Neuroscientists generate various studies to help explain many of the complex connections and functions of the brain. Most studies utilize animal models that have varying degrees of comparison to the human brain; for example, small rodents are… … Wikipedia