-
1 небаланс напряжений
небаланс напряжений
Отличие по модулю значения хотя бы одного из фазных или линейных напряжений многофазной системы электроснабжения от значений напряжений других фаз.
[ ГОСТ 23875-88]EN
voltage unbalance
phenomenon due to the differences between voltage deviations on the various phases, at a point of a polyphase system, resulting from differences between the phase currents or geometrical asymmetry in the line
[IEV number 604-01-29]
voltage unbalance (imbalance)
in a polyphase system, a condition in which the magnitudes of the phase voltages or the phase angles between consecutive phases are not all equal (fundamental component)
NOTE In three phase systems, the degree of inequality is usually expressed as the ratio of the negative and zero sequence components to the positive sequence component. In this technical report, voltage unbalance is considered in relation to three-phase systems and negative sequence only
[IEC 61000-3-13, ed. 1.0 (2008-02)]
voltage unbalance
condition in a polyphase system in which the r.m.s. values of the line voltages (fundamental component), and/or the phase angles between consecutive line voltages, are not all equal
NOTE 1 The degree of the inequality is usually expressed as the ratios of the negative- and zero-sequence components to the positive-sequence component.
NOTE 2 In this standard, voltage unbalance is considered in relation to 3-phase systems.
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
déséquilibre des tensions d'un réseau
phénomène résultant des différences de charge ou des dissymétries géométriques de lignes et qui provoque des différences entre les écarts de tension sur les diverses phases en un point d'un réseau polyphasé
[IEV number 604-01-29]
déséquilibre de tension
dans un réseau d’énergie électrique polyphasé, état dans lequel les valeurs efficaces des tensions entre conducteurs (composante fondamentale), et/ou les différences de phase entre conducteurs successifs, ne sont pas toutes égales
NOTE 1 Le taux de déséquilibre s’exprime habituellement par le rapport de la composante inverse ou homopolaire à la composante directe.
NOTE 2 Dans la présente norme, le déséquilibre de tension est relatif aux réseaux triphasés
[IEC 61000-4-30, ed. 2.0 (2008-10)]Параллельные тексты EN-RU
Voltage unbalance
Voltage unbalance on the most unbalanced phase, displayed as a percentage of Vavg.
[Schneider Electric]Небаланс напряжений
Самое значительное отличие по модулю значения одного из линейных напряжений, выраженное в процентах от среднего напряжения Vavg.
[Перевод Интент]
Недопустимые, нерекомендуемые
Тематики
EN
DE
FR
Смотри также
Русско-французский словарь нормативно-технической терминологии > небаланс напряжений
2 номинальное напряжение
номинальное напряжение
Напряжение, установленное изготовителем для прибора
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]
номинальное напряжение Uном, кВ
Номинальное междуфазное напряжение электрической сети, для работы в которой предназначены коммутационные аппараты.
[ ГОСТ Р 52726-2007]
номинальное напряжение
Un
Напряжение, применяемое для обозначения или идентификации системы электроснабжения.
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
rated voltage
voltage assigned to the appliance by the manufacturer
[IEC 60335-1, ed. 4.0 (2001-05)]
rated voltage
quantity value assigned, generally by the manufacturer, for a specified operating condition of a machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
rated voltage
input or output supply voltage for which equipment is designed or specified
[IEC 88528-11, ed. 1.0 (2004-03)]
rated voltage
specified value of the voltage at the terminals of the machine when operating at a rating. If unidirectional, the voltage is the arithmetic mean of the recurring waveform and if alternating it is the root mean square value of the fundamental frequency component of the recurring waveform
NOTE - In the case of a machine with a protective resistor permanently in series, the resistor is considered as an integral part of the machine
[IEC 60349-1, ed. 1.0 (1999-11)]
rated voltage
the value of voltage assigned by the manufacturer to a component, device or equipment and to which operation and performance characteristics are referred
NOTE - Equipment may have more than one rated voltage value or may have a rated voltage range.
[IEC 62497-1, ed. 1.0 (2010-02)]
rated voltage
reference voltage for which the cable is designed, and which serves to define the electrical tests
NOTE 1 - The rated voltage is expressed by the combination of two values: Uo/U expressed in volts (V):
Uo being the r.m.s. value between any insulated conductor and "earth" (metal covering of the cable or the surrounding medium);
U being the r.m.s. value between any two phase conductors of a multicore cable or of a system of single-core cables.
In an alternating-current system, the rated voltage of a cable is at least equal to the nominal voltage of the system for which it is intended.
This condition applies both to the value Uo and to the value U.
In a direct current system, the nominal voltage of the system is not higher than 1,5 times the rated voltage of the cable.
NOTE 2 - The operating voltage of a system may permanently exceed the nominal voltage of such a system by 10 %. A cable can be used at a 10 % higher operating voltage than its rated voltage if the latter is at least equal to the nominal voltage of the system
[IEC 60245-1, ed. 4.0 (2003-12)]
rated voltage
highest allowable voltage between the conductors in a twin and multi conductor cable, or between one conductor and an electrical conductive screen, or between the two ends of a single core cable, or earth in unscreened cables
[IEC 60800, ed. 3.0 (2009-07)]
rated voltage
the r.m.s. line-to-line voltage under rated conditions
Primary side of input transformer: ULN
Converter input: UVN
Converter output: UaN
Motor voltage: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
rated voltage
input or output voltage (for three-phase supply, the phase-to-phase voltage) as declared by the manufacturer
[IEC 62040-1, ed. 1.0 (2008-06)]
nominal voltage, Un
voltage by which a system is designated or identified
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
tension assignée
tension attribuée à l'appareil par le fabricant
[IEC 60335-1, ed. 4.0 (2001-05)]
tension nominale
tension assignée, généraleme<>value of voltage assigned by the manufacturer, to a componentnt par le constructeur pour des conditions spécifiées de fonctionnement de la machine
[IEC 60034-18-41, ed. 1.0 (2006-10)]
tension assignée
tension spécifiée aux bornes de la machine quand celle-ci fonctionne au régime assigné. Dans le cas d'une tension redressée, sa valeur est égale à la valeur moyenne de l'onde périodique. Dans le cas d'une tension alternative, sa valeur est égale à la valeur efficace de la composante fondamentale de l'onde périodique
NOTE - Dans le cas d'une machine équipée d'une résistance de protection connectée en permanence en série, la résistance est considérée comme faisant partie intégrante de la machine
[IEC 60349-1, ed. 1.0 (1999-11)]
tension assignée
valeur de la tension, assignée par le constructeur à un composant, à un dispositif ou à un matériel, et à laquelle on se réfère pour le fonctionnement et pour les caractéristiques fonctionnelles
NOTE - Les matériels peuvent avoir plusieurs valeurs ou une plage de tensions assignées.
[IEC 62497-1, ed. 1.0 (2010-02)]
tension assignée
tension de référence pour laquelle le conducteur ou le câble est prévu et qui sert à définir les essais électriques
NOTE 1 - La tension assignée est exprimée par la combinaison de deux valeurs Uo /U, exprimées en volts (V):
Uo étant la valeur efficace entre l'âme d'un conducteur isolé quelconque et la «terre» (revêtement métallique du câble au milieu environnant);
U étant la valeur efficace entre les âmes conductrices de deux conducteurs de phase quelconques d'un câble multiconducteur ou d'un système de câbles monoconducteurs ou de conducteurs.
Dans un système à courant alternatif, la tension assignée d'un conducteur ou d’un câble est au moins égale à la tension nominale du système pour lequel il est prévu.
Cette condition s'applique à la fois à la valeur Uo et à la valeur U.
Dans un système à courant continu, la tension nominale admise du système n’est pas supérieure à 1,5 fois la tension assignée du conducteur ou du câble.
NOTE 2 - La tension de service d'un système peut en permanence dépasser la tension nominale dudit système de 10 %. Un conducteur ou un câble peut être utilisé à une tension de service supérieure de 10 % à sa tension assignée si cette dernière est au moins égale à la tension nominale du système
[IEC 60245-1, ed. 4.0 (2003-12)]
tension assignée
tension maximale admissible entre les âmes dans un câble ayant une paire ou multi conducteur ou entre une âme et un écran conducteur électrique ou avec la terre pour un câble non écranté ou encore entre les deux extrémités d’un câble à âme unique
[IEC 60800, ed. 3.0 (2009-07)]
tension assignée
valeur efficace de la tension de ligne (entre phases) dans les conditions assignées
Primaire du transformateur d’entrée: ULN
Entrée du convertisseur: UVN
Sortie du convertisseur: UaN
Moteur: UAN
[IEC 61800-4, ed. 1.0 (2002-09)]
tension assignée
tension d’alimentation d’entrée ou de sortie (dans le cas d’une alimentation triphasée, tension entre phases) déclarée par le constructeur
[IEC 62040-1, ed. 1.0 (2008-06)]
tension nominale, Un
tension par laquelle un réseau est désigné ou identifié
[IEC 61000-4-30, ed. 2.0 (2008-10)]Тематики
- аппарат, изделие, устройство...
- высоковольтный аппарат, оборудование...
- прибор электрический
- электроснабжение в целом
Синонимы
- Un
EN
FR
Русско-французский словарь нормативно-технической терминологии > номинальное напряжение
3 потребляемая мощность
потребляемая мощность
Общая мощность, получаемая устройством или совокупностью устройств.
[ОСТ 45.55-99]
потребляемая мощность (электрическая)
Коэффициент, по которому электроэнергия поставляется в систему или системой, частью системы или единицей оборудования. Потребляемая мощность выражается в кВТ, кВА, или других подходящих единицах на заданный момент, или в течение определенного периода времени. Основным источником "потребляемой мощности" является энергопотребляющее оборудование потребителей (Термины Рабочей Группы правового регулирования ЭРРА).
[Англо-русский глосcарий энергетических терминов ERRA]EN
demand (electric)
The rate at which electric energy is delivered to or by a system, part of a system, or a piece of equipment. Demand is expressed in kW, kVA, or other suitable units at a given instant or over any designated period of time. The primary source of "demand" is the power-consuming equipment of the customers (ERRA Legal Regulation Working Group Terms).
[Англо-русский глосcарий энергетических терминов ERRA]
demand
the magnitude of an electricity supply, expressed in kilowatts or kilovoltamperes
[IEV ref 691-02-02]FR
puissance
importance d'une fourniture d'électricité, exprimée en kilowatts ou kilovoltampères
[IEV ref 691-02-02]Параллельные тексты EN-RU
Power demand is the energy accumulated during a specified period divided by the length of the period.
[Schneider Electric]Потребляемая мощность – это значение электрической энергии, потребленной за определенный период, поделенное на продолжительность этого периода.
[Перевод Интент]
Тематики
- электротехника, основные понятия
- энергетика в целом
EN
- absorption
- consumed power
- demand
- demand (electric)
- power consumption
- power demand
- power draw
- required power
- W
- wattage
- watts in
FR
Русско-французский словарь нормативно-технической терминологии > потребляемая мощность
4 бесперебойность электроснабжения
бесперебойность электроснабжения
-EN
continuity of supply
the quality of supply which is expressed by the extent to which the operation of an electrical system approaches the ideal state of freedom from interruption over a given period of time
[IEV ref 604-01-32]FR
continuité du service
qualité du service qui s'apprécie par la mesure dans laquelle l'exploitation du réseau s'est approchée de la situation idéale caractérisée par l'absence de toute interruption de fourniture pendant une période donnée
[IEV ref 604-01-32]2.1. Основными определяющими факторами при проектировании электроснабжения должны быть характеристики источников питания и потребителей электроэнергии, в первую очередь требование, к бесперебойности электроснабжения с учетом возможности обеспечения резервирования в технологической части проекта, требования электробезопасности.
4.4. Промышленное предприятие с электроприемниками I и II категорий должно обеспечиваться электроэнергией от двух независимых взаимно резервируемых источников питания. Выбор независимых источников питания осуществляет энергоснабжающая организация, которая в технических условиях на присоединение указывает характеристики внешних источников питания.
Из указанных характеристик разработчику проекта электроснабжения предприятия рекомендуется обратить особое внимание на ряд факторов, определяющих бесперебойность питания электроприемников при аварийном отключении одного из независимых источников питания.6.5.3. Внутрицеховые питающие силовые сети могут выполняться как магистральными, так и радиальными. Выбор вида сети зависит от планировки технологического оборудования, требований по бесперебойности электроснабжения, условий окружающей среды, вероятности изменения технологического процесса, вызывающего замену технологического оборудования, размещения цеховых ТП.
[НТП ЭПП-94]
Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > бесперебойность электроснабжения
5 включающая и отключающая способность при коротком замыкании
включающая и отключающая способность при коротком замыкании
-
[IEV number 442-05-48]EN
short-circuit (making and breaking) capacity
the alternating component of the prospective current, expressed by its rms value, which the circuit-breaker is designed to make, to carry for its opening time and to break under specified conditions
[IEV number 442-05-48]FR
pouvoir de coupure (et de fermeture) en court-circuit
composante alternative du courant présumé, exprimée en valeur efficace, que le disjoncteur, par conception, peut établir, peut supporter pendant son temps d'ouverture et peut interrompre dans des conditions spécifiées
[IEV number 442-05-48]EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > включающая и отключающая способность при коротком замыкании
6 входное полное сопротивление
входное полное сопротивление
-
[IEV number 312-06-18]EN
input impedance
impedance of the input circuit measured between the input terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the input circuit is such that the instantaneous value of the current flowing into the input terminals is a non-linear function of the instantaneous value of the input voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual input circuit, is sometimes called the "equivalent input impedance".
[IEV number 312-06-18]FR
impédance du circuit d'entrée
impédance du circuit d'entrée entre les bornes d'entrée dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit d'entrée est tel que la valeur instantanée du courant traversant les bornes d'entrée est une fonction non linéaire de la valeur instantanée de la tension d'entrée dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit d'entrée réel, est parfois appelée "impédance équivalente d'entrée".
[IEV number 312-06-18]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > входное полное сопротивление
7 выходное полное сопротивление
выходное полное сопротивление
-
[IEV number 312-06-19]EN
output impedance
impedance of the output circuit measured between the output terminals under operating conditions
NOTE 1 – The impedance can be expressed in terms of admittance.
NOTE 2 – In certain instances, for example, sampling devices or self-balancing potentiometers, the impedance can be different according to the instant when it is determined, before, during or after the instant of measurement.
NOTE 3 – When the output circuit is such that the instantaneous value of the current flowing into the output terminals is a non-linear function of the instantaneous value of the output voltage under specified conditions of frequency and voltage, the combination of resistance and reactance which would absorb the same active power and in which would flow a reactive current equal to the fundamental component that is flowing in the actual output circuit, is sometimes called the "equivalent output impedance".
[IEV number 312-06-19]FR
impédance du circuit de sortie
impédance du circuit de sortie entre les bornes de sortie dans les conditions de fonctionnement
NOTE 1 – L'impédance peut être exprimée en termes d'admittance.
NOTE 2 – Dans certains cas, par exemple les dispositifs d'échantillonnage ou les potentiomètres à rééquilibrage automatique, l'impédance peut être différente selon l’instant où elle est déterminée, avant, pendant ou après la mesure.
NOTE 3 – Lorsque le circuit de sortie est tel que la valeur instantanée du courant traversant les bornes de sortie est une fonction non linéaire de la valeur instantanée de la tension de sortie dans des conditions spécifiées de fréquence et de tension, l'impédance d'une combinaison formée par une résistance et une réactance qui absorberaient la même puissance active et dans laquelle circulerait un courant réactif égal à la composante fondamentale qui circule dans le circuit de sortie réel, est parfois appelée "impédance équivalente de sortie".
[IEV number 312-06-19]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > выходное полное сопротивление
8 гармоническая составляющая
гармоническая составляющая
Составляющая порядка выше, чем первый ряда Фурье периодической величины.
[ ГОСТ Р 51317.4.13-2006]
гармоническая составляющая
Любая из составляющих на частоте гармоники.
Значение гармонической составляющей обычно выражается среднеквадратическим значением. Для краткости вместо термина "гармоническая составляющая" допускается применение термина "гармоника".
[ ГОСТ Р 51317.4.30-2008 (МЭК 61000-4-30:2008)]EN
harmonic component
any of the components having a harmonic frequency
NOTE Its value is normally expressed as an r.m.s. value. For brevity, such component may be referred to simply as a harmonic.
[IEC 61000-4-30, ed. 2.0 (2008-10)]FR
composante harmonique
toute composante ayant une fréquence harmonique
NOTE Sa valeur est normalement exprimée sous la forme d’une valeur efficace. Pour des raisons de simplicité, cette composante peut simplement être appelée harmonique.
[IEC 61000-4-30, ed. 2.0 (2008-10)]
Помехи, представляющие собой синусоидальные напряжения и токи с частотами, кратными частоте электрической сети, обычно создаются ТС с нелинейной вольтамперной характеристикой или в результате периодической коммутации нагрузки, синхронизированной с частотой электрической сети. Указанные ТС могут рассматриваться как источники гармонических составляющих тока. Гармонические составляющие тока, создаваемые различными источниками, вызывают на полном сопротивлении электрической сети соответствующие гармонические составляющие напряжения. В результате влияния электрической емкости и индуктивности кабелей и подключения конденсаторов для коррекции коэффициента мощности в электрической сети могут возникнуть параллельные и последовательные резонансы, что приводит к увеличению гармонических составляющих напряжений, в том числе в точках электрической сети, удаленных от источников помех. Возможно также суммирование гармонических составляющих напряжения от различных источников, что учитывается при установлении требований устойчивости ТС к искажениям синусоидальности напряжения электропитания в настоящем стандарте.
Тематики
Действия
Сопутствующие термины
- гармоническая составляющая напряжения
- гармоническая составляющая тока
- источник гармонических составляющих
EN
FR
Русско-французский словарь нормативно-технической терминологии > гармоническая составляющая
9 диапазон номинальных напряжений
диапазон номинальных напряжений
Диапазон напряжений, установленный изготовителем для прибора, выраженный верхним и нижним пределами.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
rated voltage range
voltage range assigned to the appliance by the manufacturer, expressed by its lower and upper limits
[IEC 60335-1, ed. 4.0 (2001-05)]FR
plage assignée de tensions
plage des tensions attribuée à l'appareil par le fabricant, exprimée par ses limites inférieure et supérieure
[IEC 60335-1, ed. 4.0 (2001-05)]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > диапазон номинальных напряжений
10 диапазон номинальных потребляемых мощностей
диапазон номинальных потребляемых мощностей
Диапазон мощностей, установленный изготовителем для прибора, выраженный верхним и нижним пределами.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
rated power input range
power input range assigned to the appliance by the manufacturer, expressed by its lower and upper limits
[IEC 60335-1, ed. 4.0 (2001-05)]FR
plage assignée de puissances
plage de puissances attribuée à l'appareil par le fabricant, exprimée par ses limites inférieure et supérieure
[IEC 60335-1, ed. 4.0 (2001-05)]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > диапазон номинальных потребляемых мощностей
11 диапазон номинальных частот
диапазон номинальных частот
Диапазон частот, установленный изготовителем для прибора, выраженный верхним и нижним пределами.
[ ГОСТ Р 52161. 1-2004 ( МЭК 60335-1: 2001)]EN
rated frequency range
frequency range assigned to the appliance by the manufacturer, expressed by its lower and upper limits
[IEC 60335-1, ed. 4.0 (2001-05)]FR
plage assignée de fréquences
plage des fréquences attribuée à l'appareil par le fabricant, exprimée par ses limites inférieure et supérieure
[IEC 60335-1, ed. 4.0 (2001-05)]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > диапазон номинальных частот
12 диапазон регулирования (в трансформаторах)
диапазон регулирования
Диапазон изменения коэффициента ответвления, выраженный в процентах.
Примечание — Если коэффициент ответвления изменяется от 100 + а до 100 — b, то диапазон регулирования выражается в «+а %», «—b %» или «± а %», если а = B
(МЭС 421-05-07).
[ ГОСТ 30830-2002]EN
tapping range
the variation range of the tapping factor expressed as a percentage, compared with the value "100"
NOTE – If this factor ranges from 100 + a to 100 - b, the tapping range is said to be: +a % -b % or ± a % if a = b
[IEV number 421-05-07]FR
étendue de prises
étendue de variation du facteur de prise exprimé sous la forme d'un pourcentage, par rapport à la valeur "100"
NOTE – Si ce facteur varie de 100 + a à 100 - b, l'étendue de prises s'exprime par +a %, - b %ou ± a% si a = b.
[IEV number 421-05-07]Тематики
Классификация
>>>EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > диапазон регулирования (в трансформаторах)
13 длина деления шкалы
- longueur d'une division (d’échelle)
длина деления шкалы
Расстояние между осями (или центрами) двух соседних отметок шкалы, измеренное вдоль воображаемой линии, проходящей через середины самых коротких отметок шкалы.
[РМГ 29-99]EN
scale spacing
length of a scale division
distance between two successive scale marks measured on the same line as the scale length
NOTE – Scale spacing is expressed in units of length, regardless of the units of the measurand, or the units marked on the scale.
Source: VIM 4.21
[IEV number 314-01-09]FR
longueur d'une division (d’échelle)
distance entre deux repères successifs mesurée le long de la même ligne que pour la longueur d’échelle
NOTE – La longueur d’une division est exprimée en unité de longueur, quelle que soit l’unité du mesurande ou l’unité marquée sur l’échelle.
Source: VIM 4.21
[IEV number 314-01-09]Тематики
- метрология, основные понятия
EN
DE
FR
- longueur d'une division (d’échelle)
Русско-французский словарь нормативно-технической терминологии > длина деления шкалы
14 длина шкалы
- longueur d’échelle
длина шкалы
Длина линии, проходящей через центры всех самых коротких отметок шкалы средства измерений и ограниченной начальной и конечной отметками.
Примечания
1. Линия может быть реальной или воображаемой, кривой или прямой.
2. Длина шкалы выражается в единицах длины независимо от единиц, указанных на шкале.
[РМГ 29-99]EN
scale length
length of the line (curved or straight) which passes through the centres of all the shortest scale marks, contained between the first and last scale marks
NOTE – Scale length is expressed in units of length, regardless of the units of the measurand, or the units marked on the scale.
Source: ≈ VIM 4.18
[IEV number 314-01-07]FR
longueur d’échelle
longueur de la ligne (courbe ou droite) qui passe par les milieux de tous les traits les plus petits de la graduation, comprise entre le premier et le dernier trait de l'échelle
NOTE – La longueur d’échelle est exprimée en unité de longueur, quelle que soit l’unité du mesurande ou l’unité marquée sur l’échelle.
Source: ≈ VIM 4.18
[IEV number 314-01-07]Тематики
- метрология, основные понятия
EN
DE
FR
- longueur d’échelle
Русско-французский словарь нормативно-технической терминологии > длина шкалы
15 дополнительная погрешность электрического реле
- Variation de l’erreur moyenne
- variation de l'erreur moyenne
дополнительная погрешность электрического реле
Алгебраическая разность между средней погрешностью электрического реле и его средней основной погрешностью
[ ГОСТ 16022-83]EN
variation of the mean error
the algebraic difference between a mean error and the reference mean error. The variations may be expressed as an absolute value, relative value or percentage of a specified value
[IEV number 446-18-10]FR
variation de l'erreur moyenne
différence algébrique entre une erreur moyenne et l'erreur moyenne de référence. Les variations peuvent s'exprimer en valeur absolue, en valeur relative ou en pourcentage d'une valeur spécifiée
[IEV number 446-18-10]Тематики
EN
DE
FR
148. Дополнительная погрешность электрического реле
D. Einflusseffekt
E. Variation of the mean error
F. Variation de l’erreur moyenne
Алгебраическая разность между средней погрешностью электрического реле и его средней основной погрешностью
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > дополнительная погрешность электрического реле
16 емкость химического источника тока
- capacité (d’éléments ou batteries), f
емкость химического источника тока
емкость
Величина, соответствующая количеству электричества в ампер-часах, которое химический источник тока может отдать при разряде от начального до конечного напряжения при определенном режиме разряда.
[ ГОСТ 15596-82]EN
capacity (for cells or batteries)
electric charge which a cell or battery can deliver under specified discharge conditions
NOTE – The SI unit for electric charge, or quantity of electricity, is the coulomb (1 C = 1 A·s) but in practice, capacity is usually expressed in ampere hours (Ah).
[IEV number 482-03-14]FR
capacité (d’éléments ou batteries), f
charge électrique qu’un élément ou une batterie peut fournir dans des conditions de décharge spécifiées
NOTE – Dans le système international SI, l’unité de charge électrique, ou quantité d’électricité, est le coulomb (1 C = 1 A·s) mais en pratique, la capacité est généralement exprimée en ampères heures (Ah).
[IEV number 482-03-14]Тематики
Классификация
>>>Синонимы
EN
DE
FR
- capacité (d’éléments ou batteries), f
Русско-французский словарь нормативно-технической терминологии > емкость химического источника тока
17 значение величины срабатывания (возврата) электрического реле
значение величины срабатывания (возврата) электрического реле
Значение входной воздействующей или характеристической величины электрического реле, при котором оно срабатывает (возвращается) при заданных условиях
[ ГОСТ 16022-83]EN
switching value
the value of the input energizing quantity (or characteristic quantity) at which a relay switches under specified conditions
NOTE – These specified conditions can be expressed by using one of the adjectives defined under the items 446-13-27 to 446-13-29.
[IEV number 446-13-24]FR
valeur de commutation
valeur de la grandeur d'alimentation d'entrée ou de la grandeur caractéristique, pour laquelle un relais commute dans des conditions spécifiées
NOTE – Ces conditions spécifiées peuvent être exprimées par l'un des qualificatifs définis de 446-13-27 à 446-13-29.
[IEV number 446-13-24]Тематики
Классификация
>>>EN
DE
FR
71. Значение величины срабатывания (возврата) электрического реле
D. Ansprechwert
Е. Operate value
F. Valeur de fonctionnement
Значение входной воздействующей или характеристической величины электрического реле, при котором оно срабатывает (возвращается) при заданных условиях
Источник: ГОСТ 16022-83: Реле электрические. Термины и определения оригинал документа
Русско-французский словарь нормативно-технической терминологии > значение величины срабатывания (возврата) электрического реле
18 зона пропорциональности
зона пропорциональности
Величина, характеризующая изменение входного сигнала, необходимое для изменения выходного сигнала во всем диапазоне.
[ ГОСТ 9988-84]EN
proportional band of a controller
for a controller the change in input required to produce a full range change in the output caused by the proportional element only
Note – The proportional band is reciprocal to the gain of the controller and is often expressed as a percentage of the measuring span.
[IEV ref 351-28-18]FR
bande proportionnelle d'un régulateur
pour un régulateur, variation de la variable d'entrée requise pour produire sur la variable de sortie, sous le seul effet de l'élément proportionnel, une variation de toute l'étendue de cette variable
Note – La bande proportionnelle est l'inverse du gain du régulateur exprimé en pourcentage de l'intervalle de mesure.
[IEV ref 351-28-18]Тематики
- автоматизация, основные понятия
Обобщающие термины
EN
DE
- Proportionalbereich eines Reglers, m
FR
Русско-французский словарь нормативно-технической терминологии > зона пропорциональности
19 индекс устойчивости к трекингу
индекс устойчивости к трекингу
-
[IEV number 442-01-42]EN
proof tracking index
PTI (abbreviation)
the numerical value of the proof voltage expressed in volts which a material can withstand without tracking under specified test conditions
Source: 212-01-45
[IEV number 442-01-42]FR
indice de tenue au cheminement
ITC (abréviation)
valeur numérique de la tension d'épreuve exprimée en volts, qu'un matériau peut supporter sans cheminement dans des conditions d'essai spécifiées
Source: 212-01-45
[IEV number 442-01-42]EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > индекс устойчивости к трекингу
20 интеграл Джоуля I2t
интеграл Джоуля
Условная величина, характеризующая тепловое действие тока короткого замыкания на рассматриваемый элемент электроустановки, численно равная интегралу от квадрата тока короткого замыкания по времени, в пределах от начального момента короткого замыкания до момента его отключения
[ ГОСТ 26522-85]
интеграл Джоуля (I2t)
Интеграл квадрата тока за определенный период времени.
Примечания
1. Преддуговой I2t — это интеграл I2t за преддуговое время плавкого предохранителя.
2. I2t отключения — это интеграл I2t за время отключения плавкого предохранителя.
3. Энергия в джоулях, выделяемая в резисторе 1 Ом в цепи, защищаемой плавким предохранителем, равна I2t отключения, выраженному в амперах в квадрате в секунду (А2·с).
[ ГОСТ Р 50339. 0-2003 ( МЭК 60269-1-98)]
интеграл Джоуля I2t
Интеграл квадрата силы тока по данному интервалу времени.
МЭК 60050(441-18-23)
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
[ ГОСТ Р 50345-99( МЭК 60898-95)]EN
I2t
Joule integral
the integral of the square of the current over a given time interval:
NOTE 1 – The pre-arcing I2t is the I2t integral extended over the pre-arcing time of the fuse.
NOTE 2 – The operating I2t is the I2t integral extended over the operating time of the fuse.
NOTE 3 – The energy in joules liberated in one ohm of resistance in a circuit protected by a fuse is equal to the value of the operating I2t expressed in A2 • s.
[IEV number 441-18-23]FR
I2t
intégrale de Joule
intégrale du carré du courant pour un intervalle de temps donné:
NOTE 1 – L'I2t de préarc est l'intégrale I2t pour la durée de préarc du fusible.
NOTE 2 – L'I2t de fonctionnement est l'intégrale I2t pour la durée de fonctionnement du fusible.
NOTE 3 – L'énergie en joules libérée dans une portion ayant une résistance de un ohm d'un circuit protégé par un fusible est égale à la valeur de I2t de fonctionnement exprimée en A2 • s.
[IEV number 441-18-23]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > интеграл Джоуля I2t
СтраницыСм. также в других словарях:
Expressed emotion — (EE), a qualitative measure of the amount of emotion displayed, typically in the family setting, usually by a family or care takers. Theoretically, a high level of EE in the home can worsen the prognosis in patients with mental illness, (Brown et … Wikipedia
expressed — adj. 1. Communicated in words. Syn: uttered, verbalized. [WordNet 1.5] 2. Precisely and clearly expressed, leaving nothing to implication. Opposite of {implicit}. [Narrower terms: {graphic}] Also See: {definite}, {denotative}, {denotive}, {overt} … The Collaborative International Dictionary of English
Expressed Sequence Tag — Expressed Sequence Tags (EST) sind kurze DNA Sequenzen von meist 100–800 Basenpaaren Länge, die durch die teilweise Sequenzierung von cDNAs von deren 5 oder 3 Ende ausgehend gewonnen werden. Da cDNAs durch die reverse Transkription von mRNA… … Deutsch Wikipedia
expressed authority — n: express authority at authority Merriam Webster’s Dictionary of Law. Merriam Webster. 1996 … Law dictionary
expressed — expressed; un·expressed; … English syllables
Expressed sequence tag — Expressed Sequence Tags (EST) sind transkribierte Nukleotidsequenzen, die gewöhnlich durch Sequenzierung einer cDNA Bibliothek erhalten werden. Die EST Sequenzierung wurde von dem US amerikanischen Genetiker Craig Venter entwickelt und ist eine… … Deutsch Wikipedia
Expressed sequence tags — (EST) sind transkribierte Nukleotidsequenzen, die gewöhnlich durch Sequenzierung einer cDNA Bibliothek erhalten werden. Die EST Sequenzierung wurde von dem US amerikanischen Genetiker Craig Venter entwickelt und ist eine schnelle Methode (mit… … Deutsch Wikipedia
expressed — index certain (specific), oral, parol, stated, verbal Burton s Legal Thesaurus. William C. Burton. 2006 … Law dictionary
expressed command — index law Burton s Legal Thesaurus. William C. Burton. 2006 … Law dictionary
expressed concisely — index compact (pithy) Burton s Legal Thesaurus. William C. Burton. 2006 … Law dictionary
expressed desire — index request Burton s Legal Thesaurus. William C. Burton. 2006 … Law dictionary
Перевод: с русского на французский
с французского на русский- С французского на:
- Русский
- С русского на:
- Все языки
- Английский
- Немецкий
- Французский