-
1 присоединенное положение (выдвижной части)
- service position (of a removable part)
- SERVICE
- run position
- plug-in position
- draw-in
- connected position (of a removable part)
- connected position
присоединенное положение
Положение съемной или выдвижной части, в котором она полностью присоединена для выполнения предназначенной функции.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
присоединенное положение
Положение выдвижной отделяемой части НКУ, при котором она полностью соединена с ним для выполнения заданной ей функции.
[ ГОСТ Р МЭК 61439.1-2013]EN
service position (of a removable part)
connected position (of a removable part)
the position of a removable part in which it is fully connected for its intended function
[IEV number 441-16-25]
connected position
position of a removable part when it is fully connected for its intended function
[IEC 61439-1, ed. 2.0 (2011-08)]FR
position raccordée
position d'une partie amovible lorsque celle-ci est entièrement raccordée pour la fonction à laquelle elle est destinée
[IEC 61439-1, ed. 2.0 (2011-08)]
Параллельные тексты EN-RU
Рис. Schneider Electric
Draw-in
- The functional unit is operational.
- Power and auxiliaries are connected.
[Schneider Electric]Присоединённое положение
- Функциональный блок присоединён для выполнения своей функции.
- Главная и вспомогательные цепи присоединены.
[Перевод Интент]
Рис. Schneider Electric
The withdrawable drawers have 3 positions: connected, disconnected and testing.
The “ plug-in / test / draw-out” positions are mechanically marked by an indexing device associated with a mechanical indicator on the drawer sides.
[Schneider Electric]Выдвижные ящики имеют три положения: присоединенное, отсоединенное и испытательное.
Выдвижные ящики имеют три положения: присоединенное, испытательное и отсоединенное. Указанные положения промаркированы на боковых сторонах выдвижных ящиков и однозначно определяются механическим указателем.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
- выключатель автоматический
Обобщающие термины
Синонимы
EN
- connected position
- connected position (of a removable part)
- draw-in
- plug-in position
- run position
- SERVICE
- service position (of a removable part)
FR
Русско-английский словарь нормативно-технической терминологии > присоединенное положение (выдвижной части)
2 электродвигатель
electric motor
(рис. 90)
- азимутальной коррекции (гироагрегата гик) — azimuth torque motor
-, асинхронный — asynchronous motor
-, гистерезисный — hysteresis motor
синхронный эл. дв. без выступающих полюсов н возбуждения пост. током. — a synchronous motor without salient poles or direct-current excitation.
- горизонтальной коррекции (эдгк) — leveling torque motor
-, индукционный — induction motor
эл. двиг. переменного тока, у которого основная (статорная) обмотка соединяется с источником питания и взаимодействует с обмоткой ротора (обычно типа "беличье колесо") — an alternating-current motor in which the primary winding (usually the stator) is connected to the power source and induces а current into a polyphase secondary or squirred-cage secondary winding (usually the rotor).
-, исполнительный — servomotor, servo electric motor
эл. двиг. в системе сервоуправлания. обороты двигателя регулируются коррекционным эл. сигналом, усиливаемым и подаваемым в цепь электродвигателя. — а motor used in а servo system. its rotation or speed (or both) are controlled by a corrective electric signal that has been amplified and fed into the motor circuit.
-, компаундный — compound-wound motor
эл. двиг. постоянного тока с двумя отдельными обмотками возбуждения. одна обмотка включена параллельно, a другая последовательно обмотке якоря. — а d-c motor having two separate field windings. one, usually the predominant field, is connected in parallel with the armature circuit and the other is connected in series.
-, коррекционный (гироскопа) — erection torque motor /torquer/
-, сериесный — series motor
эл. двиг. с обмоткой возбуждения, включенной последовательно с обмоткой якоря. — а motor in which the field and armature circuits are connected in series.
-, синхронный — synchronous motor
an induction motor which runs at synchronous speed.
- следящей системы — servomotor
- следящей системы (рамки гироплатформы) — gimbal servomotor
-, шумовой — shunt-wound motor
эл. двиг. постоянного тока с обмоткой возбуждения, включенной параллельно обмотке якоря. — а direct-current motor in which the field circuit and armature circuit are connected in parallel.Русско-английский сборник авиационно-технических терминов > электродвигатель
3 связан
•This subfraction binds to the tissue DNA (биол.).
•These stars are bound by mutual attraction.
•The two carbon atoms are linked to a third.
•The piston of the power cylinder is linked to the damper.
•The two plants are connected by a railway.
•The bundle was tied with string.
•The camera range finder is coupled with the focusing mechanism.
•The enamel coating is bonded to metal by fusion.
•The protons are attached to carbon.
II•This phenomenon is associated (or connected) with (or is due to) magnetic storms.
•Control is directly related to the steam generation rate through the temperature coefficient.
•This is an intricate process which entails the consideration of approximating sums.
•The acceptance or rejection of the food depends upon its taste, which is usually related to its nutritive or harmful qualities.
•The rate of bleaching must be connected (or correlated) with the formation and decomposition of HOCI.
•All these tests involve the breaking of a test piece.
•A final limitation of chemical lasers has to do with the state of knowledge.
•Doubtlessly this constancy is correlated to the active role played by...
•The momentum carried by a photon is related to the photon's energy by the equation...
•Cancer patterns in Europe do not correlate with industrialization.
•The collision theory is tied to the kinetic-molecular theory.
•These are the electrons that are most directly involved in the chemical characteristics of molecules ( с которыми непосредственно связаны...).
•The production and use of ionic compounds are inevitably linked to (or with) the deterioration of the environment.
•Another uncertainty stems from the difficulty of...
•One difficulty concerns the use of hydrogen cyanide as a condensing agent.
•The rope is tied into a knot.
Русско-английский научно-технический словарь переводчика > связан
4 элементы рамной конструкции соединены жёстко
Универсальный русско-английский словарь > элементы рамной конструкции соединены жёстко
5 цепь (электрическая)
circuit (cct)
ряд соединенных проводников для прохождения эл. тока. — а number of conductors connected together for the purpose of carrying an electrical current.
соединение нескольких устроиств, образующее один или несколько каналов (контуров) для выполнения определенных электрических или радиоэлектронных функций. — the interconnection of a number of devices in oле or more closed paths to perform а desired electrical or electronic function.
- блокировки (эл.) — interlocking circuit
цепь, в которой работа одного элемента эл. оборудования зависит от окончания срабатываний других элементов. — а circuit in which the орегation of one item of electric apparatus is made dependent on the fulfilment of certain predetermined conditions on other items.
- блокировки — lock-out /locking-out/ circuit
цепь, служащая для отключения и удержания в нерабочем состоянии устройства при нарушении его нормальной работы. — function is to shut down and hold а device out of service on occurence of abnormal conditions.
- взрыва (сро) — (trsp) destruct circuit
- включена (готова к работе) — circuit armed
- возбуждения (генератора, эл. мотора) — field circuit
- галля (роликовая) — roller chain
-, гальванически развязанная — decoupling circuit
а circuit used to prevent interaction of one circuit with anotheг.
- задержки (времени) — delay circuit
цепь, обеспечивающая задержку прохождения эл. сигнала no времени, — а circuit which delays the passage of а pulse or signal from one part of a circuit t another.
- зажигания — ignition circuit
-, замкнутая — closed circuit
эл. цепь, обеспечивающая протекание эл. тока при подаче напряжения (наличии разности потенциалов), — а complete electric circuit through which current may flow when а voltage is арplied.
-, кольцевая — loop circuit
энергопитание обеспечивается по раздельным многоканальным или кольцевым цепям. — electrical energy supply is ensured by means of multichannel or loop circuits separately routed.
-, коммутационная — switching circuit
-, контрольная — monitoring /monitor/ circuit
цепь прибора (или системы). контролирующая нормальную работу прибора, и вызывающая срабатывание устройств сигнализации отказа прибора или прекращения подачи питания. — monitor circuits defect a fault in a system.
- контроля, электронная — electronic monitoring circuit
электронная цепь контроля работы пилотажного командного прибора вызывает срабатывание (появление) блейкора красного цвета в случае неисправности (неправильногo показания) прибора. — the electronic monitoring circuits within the flight director deflect red warning flaps into view if a failure occurs that will cause incorreet display.
-, многоканальная — multi-channel circuit
- нагрузки — load circuit
цепь от источника питания до нагрузки (напр., эпектронная лампа эл. двигателя) — the complete circuit required to transfer power from а source to а load (e.g., electron tube, electric motor).
-, нарушенная (эл.) — open/ broken/ circuit
-, незамкнутая — open circuit
разомкнутая цепь, не обеспечивающая протекание эл. тока, — а circuit which does not provide а complete path for the flow of current.
- обратной связи — feedback circuit
- опроса (эвм) — sampling circuit
-, параллельная — parallel circuit
цепь, в которой все положительные и отрицательные вводы и выводы соединены в соответствующих общих точках, — а circuit in which all positive terminals and negative terminals are connected to their corresponding common points.
- питания — feed/ power supply/ circuit
-, последовательная — series circuit
цепь,в которой вывод одногo сопротивления (нагрузки) соединен с вводом следующего, и т.д. — а circuit in which resistance or other components are connected end to end.
- потребителя (эл.) — load circuit
- прохождения сигнала — signal flow circuit
-, разомкнутая (разорванная) — open/ broken/ circuit
-, роликовая — roller chain
- самоконтроля — self-test circuit
- связи (между системами, блоками) — coupling circuit
- соединения на — ground circuit
- управления — control circuit
-, швартовочная (груза в кабине) — (cargo) tie-down /anchoring chain
-, электрическая — electric circuit
-, электронная — electronic circuit
обрыв ц. — broken circuit
включать в ц. — connect in circuit
сопротивление, включенное в цепь, — а resistor is connected in circuit.
закреплять на ц. — chain
крышка закреплена цепочкой к горловине, — the cap is chained to the filler.
замыкать ц. — complete/ close/ circuit
реле замыкает цепь. защищать ц. с помощью аэс — the relay completes the circuits. protect circuit by circuit breaker
размыкать (разрывать) ц. — break/ open/ circuitРусско-английский сборник авиационно-технических терминов > цепь (электрическая)
6 соединён параллельно
USAGE: соединён(ный) параллельно•Filter capacitors are connected across each resistor.
•Two parallel-connected valves...
Русско-английский научно-технический словарь переводчика > соединён параллельно
7 соединённый параллельно
USAGE: соединён(ный) параллельно•Filter capacitors are connected across each resistor.
•Two parallel-connected valves...
Русско-английский научно-технический словарь переводчика > соединённый параллельно
8 испытательное положение (выдвижной части)
испытательное положение
Положение выдвижной части, в котором соответствующие главные цепи разомкнуты на стороне питания, но не обязательно отсоединены, а вспомогательные цепи соединены для обеспечения возможности испытаний выдвижной части; при этом выдвижная часть остается механически соединенной с НКУ.
Примечание — Разомкнутое состояние главных цепей может достигаться с помощью специального устройства без механического перемещения выдвижной части.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
испытательное положение
Положение выдвижной неотделяемой части, при котором главные цепи разомкнуты на стороне питания, но не обязательно отсоединены, а вспомогательные цепи соединены для обеспечения возможности испытаний встроенных устройств, при этом выдвижная неотделяемая часть остается механически соединенной с СНКУ.
Примечание - Разомкнутое состояние главных цепей может быть достигнуто с помощью специального устройства без механического перемещения выдвижной неотделяемой части.
[ ГОСТ Р МЭК 61439.2-2012]EN
test position (of a withdrawable part)
the position of a withdrawable part in which an isolating distance or segregation is established in the main circuit and in which the auxiliary circuits are connected
[IEV number 441-16-27]FR
position d'essai (d'une partie débrochable)
position d'une partie débrochable dans laquelle une distance de sectionnement ou un cloisonnement métallique est établi dans le circuit principal et dans laquelle les circuits auxiliaires sont raccordés
[IEV number 441-16-27]
Рис. Schneider ElectricTest
- The functional unit is not operational.
- Only auxiliaries are connected.
- Padlocking is possible to keep the drawer in this position.
- Allows the functional unit testing.
- Allows maintenance on the process.
[Schneider Electric]Испытательное положение
- В этом положении функциональный блок не может выполнять функции питания нагрузки.
- Присоединены только вспомогательные цепи.
- Ящик можно зафиксировать в данном положении навесным замком.
- Можно выполнять проверку функционирования.
- Можно выполнять техническое обслуживание.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Синонимы
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > испытательное положение (выдвижной части)
9 пускатель со схемой звезда-треугольник
пускатель со схемой звезда-треугольник
Пускатель для трехфазного асинхронного двигателя, в пусковом положении которого обмотки статора соединяются звездой, а в рабочем положении — треугольником.
(МЭС 441-14-44)
[ ГОСТ Р 50030.4.1-2002 (МЭК 60947-4-1-2000)]EN
star-delta starter
a starter for a three-phase induction motor such that in the starting position the stator windings are connected in star and in the final running position they are connected in delta
[IEV number 441-14-44]FR
démarreur étoile-triangle
démarreur pour moteur à induction triphasé tel que les enroulements du stator soient connectés en étoile en position de démarrage et en triangle en position de marche
[IEV number 441-14-44][http://www.skrutka.ru/sk/tekst.php?id=50]
Схема состоит:
- Автоматический выключатель;
- Три магнитных пускателя КМ, КМ1, КМ2;
- Кнопка пуск - стоп;
- Трансформаторы тока ТТ1, ТТ2;
- Токовое реле РТ;
- Реле времени РВ;
- БКМ, БКМ1, БКМ2– блок контакт своего пускателя.
Тематики
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > пускатель со схемой звезда-треугольник
10 фотоэлектрическая установка
фотоэлектрическая установка
-
[Интент]Параллельные тексты EN-RU
Photovoltaic plants
A photovoltaic plant permits to convert the energy associated with solar irradiation into electrical energy of direct type; these plants are constituted by panels of semiconducting material, which can generate electrical power once exposed to the rays of the sun.
Photovoltaic plants can be grid-connected or supply a single load (stand alone plant).
In this last case an accumulator battery shall be present to provide power supply in case of lack of solar radiation.
The basic element of a photovoltaic plant is the photovoltaic cell constituted by semiconducting material (amorphous silicon or monocrystalline silicon); this cell, exposed to the rays of the sun, is able to supply a maximum current Impp at a maximum voltage Vmpp, which a maximum power called Wp corresponds to.
More photovoltaic cells are connected in series to form a string to raise the voltage level; by connecting more strings in parallel, the current level is increased.
For example, if a single cell can provide 5A at 35.5 Vd.c., in order to reach the level of 100A at 500 Vd.c., it is necessary to connect 20 strings in parallel, each of them constituted by 15 cells.
Generally speaking, a stand alone photovoltaic plant is constituted by the following devices:
- photovoltaic array: constituted by the photovoltaic cells suitably interconnected and used for the conversion of sunlight energy into electrical energy;
- charge regulator: it is an electronic device able to regulate charging and discharging of accumulators;
- accumulator batteries: they can provide power supply in case of lack of solar radiation;
- DC/AC inverter: it has the function of turning direct current into alternating current by controlling it and stabilizing its frequency and waveform.
The following figure shows the block diagram of a stand alone photovoltaic plant..
[ABB]Фотоэлектрические установки
Фотоэлектрические установки осуществляют прямое преобразование солнечной энергии в электрическую. Такие установки состоят из панелей полупроводникового материала, вырабатывающего электрическую энергию под воздействием солнечного излучения.
Фотоэлектрические установки являться частью общей энергосистемы или снабжать электроэнергией отдельную нагрузку (автономную установку).
В последнем случае в состав системы должна входить аккумуляторная батарея, обеспечивающая бесперебойную подачу электроэнергии в случае недостаточного солнечного излучения.
Основной частью фотоэлектрической установки являются фотоэлементы, изготовленные из полупроводникового материала (аморфного или монокристаллического кремния). При облучении солнечными лучами фотоэлемент генерирует максимальный ток Iмакс. при максимальном напряжении Uмакс, что соответствует максимальной мощности Wмакс..
Для увеличения выходного напряжения несколько фотоэлементов соединяют последовательно в ряд. Для увеличения тока несколько рядов соединяют параллельно.
Так, например, если один фотоэлемент может произвести ток 5 А при напряжении 35,5 В пост. тока, то для получения источника электроэнергии с током 100 А при напряжении 500 В пост. тока требуется соединить параллельно 20 рядов по 15 фотоэлементов в каждом.
Обычно автономная фотоэлектрическая установка состоит из следующих устройств:
- фотоэлектрическая батарея: состоит из соединенных между собой фотоэлементов, преобразующих солнечную энергию в электрическую;
- регулятор заряда: электронное устройство, предназначенное для регулирования заряда и разряда аккумуляторов;
- аккумуляторная батарея: обеспечивает электропитание нагрузки при недостаточном солнечном излучении.
- инвертор: преобразует постоянный ток в переменный ток стабильной частоты и формы.
На следующем рисунке показана функциональная схема автономной фотоэлектрической установки
[Перевод Интент]Русско-английский словарь нормативно-технической терминологии > фотоэлектрическая установка
11 шина
tire
(колеса, пневматик) (рис. 35)
- (межэлементное соединение аккумулятора) — inter-сен connector
- (электрическая) — bus, busbar
проводник (медная полоса), соединенный с источником (сетью) питания, и служащий для распределения эл. питания по цепям и фидерам — а conductor connected to the supply mains from which electric power is taken to circuits and/or feeders.
- аварийного питания (эл.) — emergency bus
-, авиационная — aircraft tire
-, автономная (с питанием от генератора no 1) — independent bus (fed by generator no. 1)
-, аккумуляторная — battery bus (ватт bus)
-, бескамерная — tubeless tire
-, вспомогательная (эл.) — secondary bus
-, выпрямительного устройствa (у штурмана, летчика) — rectifier bus (navigator's, pilot's) (rect bus, navg's, pilot's)
- генератора nо 1 (надпись) — no. 1 gen bus, gen 1 bus
-, генераторная — generator bus (gen bus)
- заземления — grounding link
-, информационная (вычисл. техника) — data bus
-, контрольная (эл.) — monitored bus
- левого борта (эл.) — left bus
-, лопнувшая (колеса) — burst tire
-, магистральная (цру питательной сети) — main distribution bus а bus connected between а generating source and busses of circuits.
- металлизации — bonding link
- на резервном источнике питания (т.е. питается от резервного источника) — bus on alternate power (source)
- низкого давления (колеса) — low-pressure tire
-, обесточенная — not powered /de-energized/ bus
-, общая (вычисл. техн.) — data bus
- объединенного питания переменным током — ас tie bus
шины 4-х генераторов соединены параллельно через реле объединения шин с шиной объединенного питания. — the four generator are connected in parallel via bus tie relays (btr's) to the ас tie bus.
- объединенного питания постоянным током — dс tie bus
данная шина соединяет параллельно выходы пост. тока четырех ву. — this bus forms а tie point to parallel dc outputs of the four tru's.
-, объединительная (пост. тока) — (dc tie bus forms a tie point to parallel dc outputs (of generators or tru's)
-, основная — main bus
система распределения электрической нагрузки включает основные и вспомогательные шины перем. и пост. тока. — electrical load distribution system includes ас and dc main and secondary busses.
- основных потребителей — essential (-services) bus
- основных потребителей перем. тока на резервном питании — essential ас bus on alternate power (source)
табло "осн. петр. на рез." загораетея при отказе основных источников пер. тока и автоматическом переходе на питание от резервных источинков питания. — the ess ас on alt is illuminated if primary ас power source has failed and automatic transfer to alternate power source has oecured.
- память — memory bus rom output data is transferred to the memory bus.
- переменного тока — ас bus
-, питающаяся от основного источника питания — bus on main power (source)
-, питающаяся от резервного источника питания — bus on alternate power (source)
- питания вспомогательных (второстепенных) потребителей — non-essential bus
- питания основных потребителей — essential bus
-, питающаяся от аккумулятора (генератора) — battery (generator) bus, bus powered by battery (generator)
- под током — powered /energized, alive, hot/ bus
- постоянного тока — dc bus
- правого борта — right bus
- распределения нагрузок (эл.) — load distribution bus
-, резервная (перем. или пост. тока) — (ас or dc standby bus
- с армированным протектором (колеса) — tread-reinforced tire coupled with relatively low inflation pressures, tire tread reinforcing is incorporated.
- соединительная — tie bus
-, спущенная (колеса) — deflated tire
при полностью спущенной шине должно обеспечиваться безопасное расстояние между возд. винтом и землей. — there must be positive clearance between propeller and ground, when critical tire is completely deflated.
-, спущенная полностью — completely deflated/flat/ tire
-, центральная распределительная — main distribution bus
напряжение на ш. напряжение на ш. аккумулятора — voltage at /on/ bus battery bus voltage
напряжение на ш. генератора — generator bus voltage
(стояночное) обжатие ш. — tire deflection
разрыв ш. (в результате перегрева) — tire explosion the tire explosion protection is in the form of fusible plugs.
включать ш. (эл.) — energize /power/ bus
восстанавливать (наваривать протектор) ш. — retread
выключать ш. (эл.) — de-energize bus
накачивать ш. — inflate tire
обесточивать ш. — de-energize bus
обнаруживать на ш. место протокола — locate tire leak
спускать воздух из ш. — deflate tireРусско-английский сборник авиационно-технических терминов > шина
12 соединены
•When the two continents were joined together,...
•The electrodes are connected to the grid.
•The ends of the tube were connected to (or with) steel castings by ball-and-socket joints.
Русско-английский научно-технический словарь переводчика > соединены
13 однофазное электротехническое устройство
однофазное электротехническое устройство
Электротехническое устройство, предназначенное для включения в однофазную электрическую цепь и не предназначенное для преобразования числа фаз.
[ ГОСТ 18311-80]EN
single-phase equipment
equipment which is connected between one line conductor and the neutral conductor
NOTE - This includes equipment in which separate loads are connected from one or more line conductors to the neutral conductor
[IEC 61000-3-12, ed. 1.0 (2004-11)]FR
matériel monophasé
matériel connecté entre un conducteur de phase et le conducteur de neutre
NOTE - Cela inclut les appareils dans lesquels des charges distinctes sont connectées entre un ou plusieurs conducteurs de phase et le conducteur de neutre.
[IEC 61000-3-12, ed. 1.0 (2004-11)]Тематики
- аппарат, изделие, устройство...
Близкие понятия
Синонимы
EN
FR
Русско-английский словарь нормативно-технической терминологии > однофазное электротехническое устройство
14 сообщаться с
•The openings are in communication (or communicate, or are connected) with an annular passage.
Русско-английский научно-технический словарь переводчика > сообщаться с
15 конкретный
•Let us take the specific case of the Earth and the Moon.
•With the particular (or specific) construction shown in Fig. 16, air filters are always supplied.
•The maximum rate of change of a particular characteristic of the orbit...
•The expansion should be allowed for in the die design for each specific (or concrete) application.
* * *Конкретный -- particular, specific, individualThe location of the particular point under consideration was also non-dimensionalized with respect to the nozzle diameter.Points representing one specific type of compressor are connected by dotted lines.The NDTT can be increased rather dramatically in some cases, depending upon the individual alloy and irradiation conditions.Русско-английский научно-технический словарь переводчика > конкретный
16 питание
supply, power
"-" (надпись у выключателя) — power, pwr
- (параметр технических данных) — power requirements power requirements... 115 vac, 400 hz
-, аэродромное (эл.) — external power (supply), (ext pwr, eps)
"- аэродромное включено" (табло) — ехt pwr avail
-, бортовое (б/с) (от бортовой электросети ла) — power from aircraft (electrical system) 27 vdc from а/с
-, дублирующее (эл.) — alternative power (alt pwr)
- к (потребителю) — supply to (consumer, load)
- кабины (система кондиционирования воздуха) — cabin /cockpit/ pneumatic (power) system
- кислородом, профилактическое (члена экипажа при длительном полете) — (crew member) oxygen supply for safety
- кислородом, терапевтическое — first-aid oxygen supply
-, наземное (эл.) — external power (supply)
-, объединенное (эл.) — tie bus power
all generators are connected in parallel to the ас tie bus.
"-от аккумулятора)" (табло) — ватт in use
"- от аккум" (надпись у выключателя) — ватт
- от (от источника питания) прибор работает от 3-фазного источника питания nеременного тока 36 в 400 гц с потребляемой мощностью 15 b'a. — supply from (power source) the instrument operates from а supply of 36 v, threephase, 400 hz ас with а consumption of 15 v'a.
- от бортовой электросети "борт" — aircraft electrical power, aircraft power (а/с pwr)
включить бортовое питание и проверить, что все аэс включены. — turn on, the aircraft electrical power and check that all circuit breakers are closed.
- от (эл.) бортсети (б/с) — power from aircraft (electrical system), (27 vdc) from aircraft
- подается (в систему) выключателем (через выключатель) — switch powers (system)
-, рабочее (эл.) — normal power (norm pwr)
- pb (реле времени) — time relay power (supply)
-, резервное (эл.) — standby power
- (топливом) самотеком "-сист. заправки вкл." — (fuel) gravity feed refuel power on
- топливом — fuel feed
выключить насосы второй левой и правой группы для выравнивания подачи питания топливом из баков данной группы. — turn off the operative 2l or 2r pumps to equalize fuel feed from 2l/2r tanks.
- топливом двигателя (n 1) — engine (1) fuel feed
- шин, резервное — bus standby power
- электроэнергией — electric power supply
"аварийное питание включено" (табло) — emer pwr in use
вилка аэродромного п. (на борту самолета, шрап) — external power receptacle
"нет (не подключено) аэр. пит." — ехт pwr not avail
розетка аэродромного п. (шрап - штепсельный разъем аэродромного питания) — external power receptacle
включать бортовое (самолетное) питание (27 в) к-л системы — energize the system with (power оf) 27 vdc derived /provided/ from aircraft (electrical system)
включать (эл.) п. (агрегата) — energize (the unit)
включать п. какого-либо агрегата — switch /turn/ on power supply to the unit
вьжлючать п. агрегата (обесточивать) — de-energize the unit
выравнивать п. топливом из лев, и прав, баков — equalize fuel feed from l and r tanks
отключать п. — turn off power (supply)
отключать п. (путем рэзъединения цепи питания) — disconnect from рower supply
подавать п. на... — supply power to...
подключать п. — connect power supply
подключать, аэродромное п. к шрап — plug external power supply (eps) in
подсоединять источник п. — connect power supply
получать п. от... — be supplied from...
питание подается от сети пост. тока через преобразователь. — роwer supply is provided from dc system through /via/ аn inverter.
оборудование получает эл. питание от шины no... — electrical supplies for the equipment arе derived from bus no....
работать от источника п. — operate from а supply (of 25 vdс)
снимать (отключать) п. — de-energizeРусско-английский сборник авиационно-технических терминов > питание
17 автоматический выключатель защиты отходящих линий
автоматический выключатель защиты отходящих линий
-Параллельные тексты EN-RU Distribution busbars, branched directly from the main busbar system, are vertically installed either on the right or on the left in the column.
They feed the outgoing circuit-breakers and are connected to them by means of rigid or flexible copper busbars, or cables.
[ABB]Распределительные шины расположены вертикально в правой или в левой части секции и подсоединены непосредственно к главным шинам.
Они подают питание на автоматические выключатели защиты отходящих линий через жесткие или гибкие медные шины или через кабели.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
- выключатель автоматический
- электроснабжение в целом
EN
Русско-английский словарь нормативно-технической терминологии > автоматический выключатель защиты отходящих линий
18 испытательное состояние
испытательное состояние
Состояние СНКУ или его части, при котором главные цепи разомкнуты на стороне питания, но не обязательно отсоединены, а вспомогательные цепи соединены для обеспечения возможности испытаний встроенных устройств.
[ ГОСТ Р МЭК 61439.2-2012]EN
test situation
condition of a PSC-assembly or part of it in which the relevant main circuits are open on its supply side but not necessarily isolated whilst the associated auxiliary circuits are connected, allowing operation tests of the incorporated devices
[IEC 61439-2, ed. 2.0 (2011-08)]FR
condition d'essai
état d'un ensemble EAP ou d'une partie de celui-ci dans lequel les circuits principaux correspondants sont ouverts en amont sans être nécessairement sectionnés et dans lequel les circuits auxiliaires associés sont raccordés, ce qui permet d'effectuer les essais de fonctionnement des dispositifs incorporés
[IEC 61439-2, ed. 2.0 (2011-08)]Тематики
- НКУ (шкафы, пульты,...)
EN
FR
Русско-английский словарь нормативно-технической терминологии > испытательное состояние
19 работа при последовательном соединении
работа при последовательном соединении
-
[IEV number 314-05-06]EN
series operation
mode of operation of stabilized power supplies in which the output terminals are connected in series, so that the output voltages of the supplies are additive
[IEV number 314-05-06]FR
fonctionnement en série
mode de fonctionnement des alimentations stabilisées dans lequel les bornes de sortie sont connectées en série, de telle sorte que les tensions de sortie s'ajoutent
[IEV number 314-05-06]Тематики
- измерение электр. величин в целом
EN
DE
FR
Русско-английский словарь нормативно-технической терминологии > работа при последовательном соединении
20 резервирование с развязкой источников электропитания
резервирование с развязкой источников электропитания
-
Рис. ABB
True redundancy using a CP-A RUFor true redundancy it is necessary to provide decoupling of the individual power supplies.
Otherwise, the failed power supply could possibly act as a load for the other power supply or, in the worst case, cause a short circuit on the secondary side resulting in a failure of the second power supply.
Decoupling of the power supplies has to be performed by connecting decoupling diodes (so called O-ring diodes) to the secondary outputs. These diodes prevent mutual loading of the power supplies in case of a fault and thus guarantee continuous supply.
For the setup of redundant power supply systems, ABB offers two redundancy units, the CP-RUD (for output currents of up to 5 A) and the CP-A RU (for output currents of up to 40 A). The inputs of these units are connected to the terminals L+ and L- of the power supplies (many other manufacturers often consider L+ only). The loads are supplied directly from the outputs of the redundancy unit.
[ABB]Тематики
EN
Русско-английский словарь нормативно-технической терминологии > резервирование с развязкой источников электропитания
См. также в других словарях:
Connected space — For other uses, see Connection (disambiguation). Connected and disconnected subspaces of R² The green space A at top is simply connected whereas the blue space B below is not connected … Wikipedia
Connected component (graph theory) — A graph with three connected components. In graph theory, a connected component of an undirected graph is a subgraph in which any two vertices are connected to each other by paths, and which is connected to no additional vertices. For example,… … Wikipedia
connected — con|nect|ed [ kə nektəd ] adjective * 1. ) joined to each other or to something else: connected underground tunnels The dishwasher isn t connected yet. 2. ) things such as ideas, events, or facts that are connected are related to each other: Were … Usage of the words and phrases in modern English
connected */ — UK [kəˈnektɪd] / US [kəˈnektəd] adjective 1) a) things such as ideas, events, or facts that are connected are related to each other Were the two deaths connected? connected with/to: a meeting to discuss issues connected with genetic engineering… … English dictionary
Connected pawns — a b c d e f g h … Wikipedia
connected — adjective 1 if two things are connected, they are joined together: The two continents were once connected. (+ to): The wire is connected to an electrode. 2 if two facts, events, etc are connected, they affect each other or are related to each… … Longman dictionary of contemporary English
Connected ring — In mathematics, especially in the field of commutative algebra, a connected ring is a commutative ring A that satisfies one of the following equivalent conditions: A possesses no non trivial (that is, not equal to 1 or 0) idempotent elements; the … Wikipedia
connected — con|nect|ed [kəˈnektıd] adj ▬▬▬▬▬▬▬ 1¦(joined)¦ 2¦(relationship)¦ 3 well connected ▬▬▬▬▬▬▬ 1.) ¦(JOINED)¦ to be joined to something else or joined to a large system or network connected to ▪ The light is connected to a timer. ▪ a computer… … Dictionary of contemporary English
Connected Health — is a term used to describe a model for healthcare delivery that uses technology to provide healthcare remotely. Connected health aims to maximize healthcare resources and provide increased, flexible opportunities for consumers to engage with… … Wikipedia
Connected-component labeling — (alternatively connected component analysis, blob extraction, region labeling, blob discovery, or region extraction) is an algorithmic application of graph theory, where subsets of connected components are uniquely labeled based on a given… … Wikipedia
Connected Mathematics — is a comprehensive, problem centered curriculum designed for all students in grades 6 8 based on the NCTM standards. The curriculum was developed by the Connected Mathematics Project (CMP) at Michigan State University and funded by the National… … Wikipedia
Перевод: с русского на английский
с английского на русский- С английского на:
- Русский
- С русского на:
- Все языки
- Английский
- Немецкий
- Французский