-
1 водосборная система
водосборная система
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
drainage system
A surface stream, or a body of impounded surface water, together with all other such streams and water bodies that are tributary to it and by which a region is drained. An artificial drainage system includes also surface and subsurface conduits. (Source: BJGEO)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > водосборная система
-
2 изменение климата
изменение климата
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
climatic change
The long-term fluctuations in temperature, precipitation, wind, and all other aspects of the Earth's climate. External processes, such as solar-irradiance variations, variations of the Earth's orbital parameters (eccentricity, precession, and inclination), lithosphere motions, and volcanic activity, are factors in climatic variation. Internal variations of the climate system, e.g., changes in the abundance of greenhouse gases, also may produce fluctuations of sufficient magnitude and variability to explain observed climate change through the feedback processes interrelating the components of the climate system. (Source: GSFC)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > изменение климата
-
3 культура по отношению к окружающей среде
культура по отношению к окружающей среде
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
environmental culture
The total of learned behavior, attitudes, practices and knowledge that a society has with respect to maintaining or protecting its natural resources, the ecosystem and all other external conditions affecting human life. (Source: ANT / TOE)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > культура по отношению к окружающей среде
-
4 напряжение относительно земли
напряжение относительно земли
UO
а) в распределительных сетях с заземленной нейтралью - напряжение между фазным проводником и заземленной нейтралью;
б) во всех других распределительных сетях - напряжение между незаземленными фазными проводниками и землей, когда один из фазных проводников накоротко соединен с землей.
[ ГОСТ Р 61557-1-2006]EN
voltage against earth, Uo
a) in distribution systems with an earthed neutral point, the voltage between a phase conductor and the earthed neutral point;
b) in all other distribution systems, the voltage present between the remaining phase conductors and earth when one of the phase conductors is shorted to earth
[IEC 61557-1, ed. 2.0 (2007-01)]FR
tension par rapport à la terre, Uo
a) dans un réseau de distribution dont le point neutre est mis à la terre, la tension d’un conducteur de phase par rapport au point neutre mis à la terre;
b) dans les autres types de réseaux de distribution, la tension qui apparaît entre la terre et les phases restantes lorsque l’une des phases est mise à la terre
[IEC 61557-1, ed. 2.0 (2007-01)]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > напряжение относительно земли
-
5 полосовой фильтр
полосовой фильтр
Ндп. фильтр полосового типа
Электрический частотный фильтр, имеющий полосу пропускания, расположенную между двумя частотами среза
[ ГОСТ 24375-80]
полосовой фильтр
Фильтр, пропускающий сигналы с частотами, лежащими в пределах между нижней и верхней граничными частотами, и задерживающий остальные сигналы
[Система неразрушающего контроля. Виды (методы) и технология неразрушающего контроля. Термины и определения (справочное пособие). Москва 2003 г.]
полосовой фильтр
-
[IEV number 151-13-58]EN
band-pass filter
filter having a single pass-band with specified cut-off frequencies different from zero or infinite
[IEV number 151-13-58]FR
filtre passe-bande, m
filtre dont l'unique bande passante est limitée par deux fréquences de coupure spécifiées, finies et non nulles
[IEV number 151-13-58]Параллельные тексты EN-RU
Band pass filter
The output only transmits the 50 Hz component of the input signals.
All other frequencies (above and below 50 Hz) are attenuated.
[Schneider Electric]Полосовой фильтр
На выход элемента передаются только входные сигналы частотой 50 Гц.
Все частоты выше и ниже 50 Гц подавляются.
[Перевод Интент]Недопустимые, нерекомендуемые
Тематики
EN
- band filter
- band pass
- band pass filter
- band-pass filter
- bandpass filter
- bandwidth filter
- BP
- BW filter
- filter band pass
- gap filler
- pass-band filter
- passband filter
- zonal filter
DE
FR
Русско-французский словарь нормативно-технической терминологии > полосовой фильтр
-
6 район преимущественного права покупки (земельного участка)
район преимущественного права покупки (земельного участка)
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
pre-emption zone
Areas that are subject to the pre-emption right which is a privilege accorded by the government to the actual settler upon a certain limited portion of the public domain, to purchase such tract at a fixed price to the exclusion of all other applicants. (Source: BLACKa)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > район преимущественного права покупки (земельного участка)
-
7 цикл срабатываний
цикл срабатываний контактного коммутационного аппарата
Последовательность переходов из одного положения в другое и обратно в первое через все прочие положения, если они имеются.
МЭК 60050(441-16-02).
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]
цикл оперирования1)
-
[IEV number 442-01-50]EN
operating cycle (of a mechanical switching device)
a succession of operations from one position to another and back to the first position through all other positions, if any
[IEV number 441-16-02]
operating cycle
a succession of operations from one position to another and back to the first position
Source: 441-16-02 MOD
[IEV number 442-01-50]FR
cycle de manoeuvres (d'un appareil mécanique de connexion)
suite de manoeuvres d'une position à une autre avec retour à la première position en passant par toutes les autres positions, s'il en existe
[IEV number 441-16-02]
cycle de manoeuvres
suite de manoeuvres d'une position à une autre et retour à la première position
Source: 441-16-02 MOD
[IEV number 442-01-50]1) правильно - цикл срабатываний
[Интент]
См. также коммутационный циклТематики
- аппарат, изделие, устройство...
Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > цикл срабатываний
-
8 электрическое разделение
- séparation (électrique), f
(электрическое) разделение
Мера защиты, обеспечивающая изоляцию опасных токоведущих частей от всех других электрических цепей и частей, от локальной земли и от прикосновения
[ ГОСТ Р МЭК 60050-826-2009]EN
(electrical) separation
protective measure in which hazardous-live-parts are insulated from all other electric circuits and parts, from local earth and from touch
[IEV number 826-12-27]FR
séparation (électrique), f
mesure de protection dans laquelle les parties actives dangereuses sont isolées de tous les autres circuits électriques et parties, de la terre locale et de tout contact
[IEV number 826-12-27]Тематики
EN
DE
- elektrische Schutztrennung, f
FR
- séparation (électrique), f
Русско-французский словарь нормативно-технической терминологии > электрическое разделение
-
9 НКУ распределения и управления
низковольтное устройство распределения и управления (НКУ)
Низковольтные коммутационные аппараты и устройства управления, измерения, сигнализации, защиты, регулирования, собранные совместно, со всеми внутренними электрическими и механическими соединениями и конструктивными элементами.
[ ГОСТ Р МЭК 61439-1-2012]
низковольтное устройство распределения и управления
Комбинация низковольтных коммутационных аппаратов с устройствами управления, измерения, сигнализации, защиты, регулирования и т. п., полностью смонтированных изготовителем НКУ (под его ответственность на единой конструктивной основе) со всеми внутренними электрическими и механическими соединениями с соответствующими конструктивными элементами
Примечания
1. В настоящем стандарте сокращение НКУ используют для обозначения низковольтных комплектных устройств распределения и управления.
2. Аппараты, входящие в состав НКУ, могут быть электромеханическими или электронными.
3. По различным причинам, например по условиям транспортирования или изготовления, некоторые операции сборки могут быть выполнены на месте установки, вне предприятия-изготовителя.
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]EN
power switchgear and controlgear assembly (PSC-assembly)
low-voltage switchgear and controlgear assembly used to distribute and control energy for all types of loads, intended for industrial, commercial and similar applications where operation by ordinary persons is not intended
[IEC 61439-2, ed. 1.0 (2009-01)]
low-voltage switchgear and controlgear assembly
combination of one or more low-voltage switching devices together with associated control, measuring, signalling, protective, regulation equipment, etc., completely assembled under the responsibility of the manufacturer with all the internal electrical and mechanical interconnections and structural parts.
[IEC 61892-3, ed. 2.0 (2007-11)]
switchgear and controlgear
a general term covering switching devices and their combination with associated control, measuring, protective and regulating equipment, also assemblies of such devices and equipment with associated interconnections, accessories, enclosures and supporting structures
[IEV number 441-11-01]
switchgear and controlgear
electric equipment intended to be connected to an electric circuit for the purpose of carrying out one or more of the following functions: protection, control, isolation, switching
NOTE – The French and English terms can be considered as equivalent in most cases. However, the French term has a broader meaning than the English term and includes for example connecting devices, plugs and socket-outlets, etc. In English, these latter devices are known as accessories.
[IEV number 826-16-03 ]
switchboard
A large single electric control panel, frame, or assembly of panels on which are mounted (either on the back or on the face, or both) switches, overcurrent and other protective devices, buses, and usually instruments; not intended for installation in a cabinet but may be completely enclosed in metal; usually is accessible from both the front and rear.
[ McGraw-Hill Dictionary of Architecture & Construction]
switchboard
One or more panels accommodating control switches, indicators, and other apparatus for operating electric circuits
[ The American Heritage Dictionary of the English Language]FR
ensemble d'appareillage de puissance (ensemble PSC)
ensemble d'appareillage à basse tension utilisé pour répartir et commander l'énergie pour tous les types de charges et prévu pour des applications industrielles, commerciales et analogues dans lesquelles l'exploitation par des personnes ordinaires n'est pas prévue
[IEC 61439-2, ed. 1.0 (2009-01)]
appareillage, m
matériel électrique destiné à être relié à un circuit électrique en vue d'assurer une ou plusieurs des fonctions suivantes: protection, commande, sectionnement, connexion
NOTE – Les termes français et anglais peuvent être considérés comme équivalents dans la plupart des cas. Toutefois, le terme français couvre un domaine plus étendu que le terme anglais, et comprend notamment les dispositifs de connexion, les prises de courant, etc. En anglais, ces derniers sont dénommés "accessories".
[IEV number 826-16-03 ]
appareillage
terme général applicable aux appareils de connexion et à leur combinaison avec des appareils de commande, de mesure, de protection et de réglage qui leur sont associés, ainsi qu'aux ensembles de tels appareils avec les connexions, les accessoires, les enveloppes et les charpentes correspondantes
[IEV number 441-11-01]
A switchboard as defined in the National Electrical Code is a large single panel, frame, or assembly of panels on which are mounted, on the face or back or both switches, overcurrent and other protective devices, buses, and, usually, instruments.
Switchboards are generally accessible from the rear as well as from the front and are not intended to be installed in cabinets.
The types of switchboards, classified by basic features of construction, are as follows:
1. Live-front vertical panels
2. Dead-front boards
3. Safety enclosed boards( metal-clad)
[American electricians’ handbook]
The switchboard plays an essential role in the availability of electric power, while meeting the needs of personal and property safety.
Its definition, design and installation are based on precise rules; there is no place for improvisation.
The IEC 61439 standard aims to better define " low-voltage switchgear and controlgear assemblies", ensuring that the specified performances are reached.
It specifies in particular:
> the responsibilities of each player, distinguishing those of the original equipment manufacturer - the organization that performed the original design and associated verification of an assembly in accordance with the standard, and of the assembly manufacturer - the organization taking responsibility for the finished assembly;
> the design and verification rules, constituting a benchmark for product certification.
All the component parts of the electrical switchboard are concerned by the IEC 61439 standard.
Equipment produced in accordance with the requirements of this switchboard standard ensures the safety and reliability of the installation.
A switchboard must comply with the requirements of standard IEC 61439-1 and 2 to guarantee the safety and reliability of the installation.
Managers of installations, fully aware of the professional and legal liabilities weighing on their company and on themselves, demand a high level of safety for the electrical installation.
What is more, the serious economic consequences of prolonged halts in production mean that the electrical switchboard must provide excellent continuity of service, whatever the operating conditions.
[Schneider Electric]НКУ играет главную роль в обеспечении электроэнергией, удовлетворяя при этом всем требованиям по безопасности людей и сохранности имущества.
Выбор конструкции, проектирование и монтаж основаны на чётких правилах, не допускающих никакой импровизации.
Требования к низковольтным комплектным устройствам распределения и управления сформулированы в стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000).
В частности, он определяет:
> распределение ответственности между изготовителем НКУ - организацией, разработавшей конструкцию НКУ и проверившей его на соответствие требованиям стандарта, и сборщиком – организацией, выполнившей сборку НКУ;
> конструкцию, технические характеристики, виды и методы испытаний НКУ.
В стандарте МЭК 61439 (ГОСТ Р 51321. 1-2000) описываются все компоненты НКУ.
Оборудование, изготовленное в соответствии с требованиями этого стандарта, обеспечивает безопасность и надежность электроустановки.
Для того чтобы гарантировать безопасность эксплуатации и надежность работы электроустановки, распределительный щит должен соответствовать требованиям стандарта МЭК 61439-1 и 2.
Лица, ответственные за электроустановки, должны быть полностью осведомлены о профессиональной и юридической ответственности, возложенной на их компанию и на них лично, за обеспечение высокого уровня безопасности эксплуатации этих электроустановок.
Кроме того, поскольку длительные перерывы производства приводят к серьезным экономическим последствиям, электрический распределительный щит должен обеспечивать надежную и бесперебойную работу независимо от условий эксплуатации.
[Перевод Интент]LV switchgear assemblies are undoubtedly the components of the electric installation more subject to the direct intervention of personnel (operations, maintenance, etc.) and for this reason users demand from them higher and higher safety requirements.
The compliance of an assembly with the state of the art and therefore, presumptively, with the relevant technical Standard, cannot be based only on the fact that the components which constitute it comply with the state of the art and therefore, at least presumptively, with the relevant technical standards.
In other words, the whole assembly must be designed, built and tested in compliance with the state of the art.
Since the assemblies under consideration are low voltage equipment, their rated voltage shall not exceed 1000 Va.c. or 1500 Vd.c. As regards currents, neither upper nor lower limits are provided in the application field of this Standard.
The Standard IEC 60439-1 states the construction, safety and maintenance requirements for low voltage switchgear and controlgear assemblies, without dealing with the functional aspects which remain a competence of the designer of the plant for which the assembly is intended.
[ABB]Низковольтные комплектные устройства (НКУ), вне всякого сомнения, являются частями электроустановок, которые наиболее подвержены непосредственному вмешательству оперативного, обслуживающего и т. п. персонала. Вот почему требования потребителей к безопасности НКУ становятся все выше и выше.
Соответствие НКУ современному положению дел и вследствие этого, гипотетически, соответствующим техническим стандартам, не может основываться только на том факте, что составляющие НКУ компоненты соответствуют современному состоянию дел и поэтому, по крайней мере, гипотетически, - соответствующим техническим стандартам
Другими словами, НКУ должно быть разработано, изготовлено и испытано в соответствии с современными требованиями.
Мы рассматриваем низковольтные комплектные устройства и это означает, что их номинальное напряжение не превышает 1000 В переменного тока или 1500 В постоянного тока. Что касается тока, то ни верхнее, ни нижнее значение стандартами, относящимися к данной области, не оговариваются
Стандарт МЭК 60439-1 устанавливает требования к конструкции, безопасности и техническому обслуживанию низковольтных комплектных устройств без учета их функций, полагая, что функции НКУ являются компетенцией проектировщиков электроустановки, частью которых эти НКУ являются.
[Перевод Интент]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Действия
Синонимы
Сопутствующие термины
EN
- assembly
- electrical switchboard
- low voltage controlgear and assembly
- low voltage switchboard
- low voltage switchgear and controlgear assembly
- low-voltage switchgear and controlgear assembly
- LV switchgear and controlgear assembly
- LV switchgear assembly
- panel
- power switchgear and controlgear assembly
- PSC-assembly
- switchboard
- switchgear and controlgear
- switchgear/controlgear
DE
- Schaltanlagen und/oder Schaltgeräte
FR
Русско-французский словарь нормативно-технической терминологии > НКУ распределения и управления
-
10 нарушение условий конкуренции
нарушение условий конкуренции
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
distortion of competition
Article 85(1) of the EEC Treaty prohibits all agreements between undertakings, decisions by associations of undertakings and concerted practices which may affect trade between member states and which have as their object or effect the prevention, restriction or distortion of competition within the common market. All such arrangements are automatically null and void under Article 85(2), unless exempted by the Commission pursuant to Article 85(3). The text of Article 85 is as follows: "1. The following shall be prohibited as incompatible with the common market: all agreements between undertakings, decisions by associations of undertakings and concerted practices which may affect trade between member states and which have as their object or effect the prevention, restriction or distortion of competition within the common market, and in particular those which: (a) directly or indirectly fix purchase or selling prices or any other trading conditions; (b) limit or control production, markets, technical development, or investment; (c) share markets or sources of supply; (d) apply dissimilar conditions to equivalent transactions with other trading parties, thereby placing them at a competitive disadvantage; (e) make the conclusion of contracts subject to acceptance by the other parties of supplementary obligations which, by their nature or according to commercial usage, have no connection with the subject of such contracts. (Source: CLAORG)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > нарушение условий конкуренции
-
11 ограничение конкуренции
ограничение конкуренции
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
restriction on competition
Article 85(1) of the EEC Treaty prohibits all agreements between undertakings, decisions by associations of undertakings and concerted practices which may affect trade between member states and which have as their object or effect the prevention, restriction or distortion of competition within the common market. All such arrangements are automatically null and void under Article 85(2), unless exempted by the Commission pursuant to Article 85(3). The text of Article 85 is as follows: "1. The following shall be prohibited as incompatible with the common market: all agreements between undertakings, decisions by associations of undertakings and concerted practices which may affect trade between member states and which have as their object or effect the prevention, restriction or distortion of competition within the common market, and in particular those which: (a) directly or indirectly fix purchase or selling prices or any other trading conditions; (b) limit or control production, markets, technical development, or investment; (c) share markets or sources of supply; (d) apply dissimilar conditions to equivalent transactions with other trading parties, thereby placing them at a competitive disadvantage; (e) make the conclusion of contracts subject to acceptance by the other parties of supplementary obligations which, by their nature or according to commercial usage, have no connection with the subject of such contracts. (Source: CLAORG)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ограничение конкуренции
-
12 ДДТ
ДДТ
—
[ http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]EN
DDT
A persistent organochlorine insecticide, also known as dichlorodiphenyltrichloroethane, that was introduced in the 1940s and used widely because of its persistence (meaning repeated applications were unnecessary), its low toxicity to mammals and its simplicity and cheapness of manufacture. It became dispersed all over the world and, with other organochlorines, had a disruptive effect on species high in food chains, especially on the breeding success of certain predatory birds. DDT is very stable, relatively insoluble in water, but highly soluble in fats. Health effects on humans are not clear, but it is less toxic than related compounds. It is poisonous to other vertebrates, especially fish, and is stored in the fatty tissue of animals as sublethal amounts of the less toxic DDE. Because of its effects on wildlife its use in most countries is now forbidden or strictly limited. (Source: MGH / ALL)
[http://www.eionet.europa.eu/gemet/alphabetic?langcode=en]Тематики
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > ДДТ
-
13 распределительное устройство
распределительное устройство
Распределительным устройством (РУ) называется электроустановка, служащая для приема и распределения электроэнергии и содержащая сборные и соединительные шины, коммутационные аппараты, вспомогательные устройства (компрессорные, аккумуляторные и др.), а также устройства защиты, автоматики и измерительные приборы.
[РД 34.20.185-94]
распределительное устройство
Электроустановка, предназначенная для приема и распределения электрической энергии на одном напряжении и содержащая коммутационные аппараты и соединяющие их сборные шины [секции шин], устройства управления и защиты.
Примечание. К устройствам управления относятся аппараты и связывающие их элементы обеспечивающие контроль, измерение, сигнализацию и выполнение команд.
[ ГОСТ 24291-90]
[ ГОСТ Р 53685-2009]
электрическое распределительное устройство
распределительное устройство
Устройство, предназначенное для приема и распределения электроэнергии на одном напряжении и содержащее коммутационные аппараты и соединяющие их сборные соединительные устройства.
Примечание. В состав распределительного устройства дополнительно могут входить устройства защиты и управления
[ОСТ 45.55-99]
распределительное устройство
Электроустановка, служащая для приема и распределения электроэнергии и содержащая коммутационные аппараты, сборные и соединительные шины, вспомогательные устройства (компрессорные, аккумуляторные и др.), а также устройства защиты, автоматики и измерительные приборы.
[ПОТ Р М-016-2001]
[РД 153-34.0-03.150-00]
устройство распределительное
Совокупность аппаратов и приборов для приёма и распределения электроэнергии одного напряжения, вырабатываемой электростанцией или преобразуемой подстанцией
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
switching substation
a substation which includes switchgear and usually busbars, but no power transformers
[IEV number 605-01-02]FR
poste de sectionnement
poste de coupure
poste comprenant des organes de manoeuvre et généralement des jeux de barres, à l'exclusion de transformateurs de puissance
[IEV number 605-01-02]В качестве РУ 6—10 кВ используется сборка высокого напряжения с однополюсными разъединителями и вертикальным расположением фаз одного присоединения и одна камера КСО с выключателем нагрузки и предохранителями для подключения трансформатора. Для РУ 0,4 кВ применяются сборки низкого напряжения с предохранителями и вертикальным расположением фаз одного присоединения.
На ПС применяются открытые (ОРУ), закрытые (ЗРУ) или комплектные (КРУ) распределительные устройства.
[ http://energy-ua.com/elektricheskie-p/klassifikatsiya.html]
В общем случае ПС и РУ являются составной частью электроустановок, которые различаются:
-
по назначению:
- генерирующие,
- преобразовательно-распределительные,
-
потребительские.
Генерирующие электроустановки служат для выработки электроэнергии, преобразовательно-распределительные электроустановки преобразуют электроэнергию в удобный для передачи и потребления вид, передают ее и распределяют между потребителями;
-
по роду тока:
- постоянного тока,
- переменного тока.
-
по напряжению:
- до 1000 В,
- выше 1000 В.
ГОСТ 29322—92 установлена следующая шкала номинальных напряжений:
Шкала номинальных напряжений ограничена сравнительно небольшим числом стандартных значений, благодаря чему изготавливается небольшое число типоразмеров машин и оборудования, а электросети выполняются более экономичными. В установках трехфазного тока номинальным напряжением принято считать напряжение между фазами (междуфазовое напряжение). Согласнодля электросетей переменного тока частотой 50 Гц междуфазовое напряжение должно быть: 12, 24, 36, 42, 127, 220, 380 В; 3, 6, 10, 20, 35, 110, 150, 220, 330, 500, 750 и 1150 кВ;
для электросетей постоянного тока: 12, 24, 36, 48, 60, 110, 220, 440, 660, 825, 3000 В и выше.-
по способу присоединения к электросети ПС разделяются на:
- тупиковые (блочные),
- ответвительные (блочные),
- проходные (транзитные)
- узловые.
Тупиковые ПС получают питание по одной или двум тупиковым ВЛ.
Ответвительные ПС присоединяются ответвлением к одной или двум проходящим ВЛ с односторонним или двухсторонним питанием.
Проходные ПС включаются в рассечку одной или двух проходящих ВЛ с односторонним или двухсторонним питанием.
Узловые ПС кроме питающих имеют отходящие радиальные или транзитные ВЛ.-
по способу управления ПС могут быть:
- только с телесигнализацией,
- телеуправляемыми с телесигнализацией,
- с телесигнализацией и управлением с общеподстанционного пункта управления (ОПУ).
Подстанции оперативно обслуживаются постоянным дежурным персоналом на щите управления, дежурными на дому или оперативно-выездными бригадами (ОВБ). Ремонт ПС осуществляется специализированными выездными бригадами централизованного ремонта или местным персоналом подстанции.
В РУ напряжением до 1000 В провода, шины, аппараты, приборы и конструкции выбирают как по нормальным условиям работы (напряжению и току), так и по термическим и динамическим воздействиям токов коротких замыканий (КЗ) или предельно допустимой отключаемой мощности.
В РУ и ПС напряжением выше 1000 В расстояния между электрооборудованием, аппаратами, токоведущими частями, изоляторами, ограждениями и конструкциями устанавливаются так, чтобы при нормальном режиме работы электроустановки возникающие физические явления (температура нагрева, электрическая дуга, выброс газов, искрение и др.) не могли привести к повреждению оборудования и КЗ.[ http://energy-ua.com/elektricheskie-p/klassifikatsiya.html]
Several different classifications of switchgear can be made:- By the current rating.
-
By interrupting rating (maximum short circuit current that the device can safely interrupt)
- Circuit breakers can open and close on fault currents
- Load-break/Load-make switches can switch normal system load currents
- Isolators may only be operated while the circuit is dead, or the load current is very small.
-
By voltage class:
- Low voltage (less than 1,000 volts AC)
- Medium voltage (1,000–35,000 volts AC)
- High voltage (more than 35,000 volts AC)
-
By insulating medium:
-
By construction type:
- Indoor (further classified by IP (Ingress Protection) class or NEMA enclosure type)
- Outdoor
- Industrial
- Utility
- Marine
- Draw-out elements (removable without many tools)
- Fixed elements (bolted fasteners)
- Live-front
- Dead-front
- Open
- Metal-enclosed
- Metal-clad
- Metal enclosed & Metal clad
- Arc-resistant
-
By IEC degree of internal separation
- No Separation (Form 1)
- Busbars separated from functional units (Form 2a, 2b, 3a, 3b, 4a, 4b)
- Terminals for external conductors separated from busbars (Form 2b, 3b, 4a, 4b)
- Terminals for external conductors separated from functional units but not from each other (Form 3a, 3b)
- Functional units separated from each other (Form 3a, 3b, 4a, 4b)
- Terminals for external conductors separated from each other (Form 4a, 4b)
- Terminals for external conductors separate from their associated functional unit (Form 4b)
-
By interrupting device:
-
By operating method:
- Manually operated
- Motor/stored energy operated
- Solenoid operated
-
By type of current:
-
By application:
-
By purpose
- Isolating switches (disconnectors)
- Load-break switches.
- Grounding (earthing) switches
A single line-up may incorporate several different types of devices, for example, air-insulated bus, vacuum circuit breakers, and manually operated switches may all exist in the same row of cubicles.
Ratings, design, specifications and details of switchgear are set by a multitude of standards. In North America mostly IEEE and ANSI standards are used, much of the rest of the world uses IEC standards, sometimes with local national derivatives or variations.
[Robert W. Smeaton (ed) Switchgear and Control Handbook 3rd Ed., Mc Graw Hill, new York 1997]
[ http://en.wikipedia.org/wiki/High_voltage_switchgear]Тематики
- электрификация, электроснабж. железных дорог
- электроагрегаты генераторные
- электробезопасность
- электроснабжение в целом
Синонимы
EN
- distribution
- energy distribution board
- gear
- switch-gear
- switchboard
- switchgear
- switching substation
- switchyard
DE
FR
Русско-французский словарь нормативно-технической терминологии > распределительное устройство
-
по назначению:
-
14 комплектное распределительное устройство в металлической оболочке
- pareillage d’armoire
- appareillage sous enveloppe métallique
- appareillage recouvert de métal
- appareillage à compartiments (avec cloisons non métalliques)
комплектное распределительное устройство в металлической оболочке
-EN
metal-enclosed switchgear
switchgear assemblies with an external metallic enclosure intended to be earthed and complete except for external connections
NOTE The metal-enclosed switchgear is subdivided into three types:
– metal-clad switchgear;
– compartmented switchgear (with one or more non-metallic partitions);
– cubicle switchgear
[IEC 61992-1, ed. 2.0 (2006-02)]
metal-clad switchgear
metal-enclosed switchgear in which components are arranged in separate compartments with metal partitions intended to be earthed
NOTE 1 This term applies to metal-enclosed switchgear with metal partitions providing the degree of protection (or higher) included in IEC 61992-6 and having separate compartments at least for the following components:
– each main switching device;
– components connected to one side of a main switching device, for example, feeder circuit;
– components connected to the other side of the main switching device, for example, busbars; where more than one set of busbars is provided, each set is in a separate compartment.
NOTE 2 Metal-enclosed switchgear having metal partitions and meeting all the requirements of NOTE 1 may utilise an insulating shutter barrier as a part of a shutter arrangement, the combination of which provides the degree of protection included in Table 1 of IEC 61992-6 (or higher) and satisfies the requirements of the standard for partitions and shutters made of insulating material.
[IEC 61992-1, ed. 2.0 (2006-02)]
compartmented switchgear (with non-metallic partitions)
metal-enclosed switchgear in which components are arranged in separate compartments as for metal-clad switchgear, but with one or more non-metallic partitions providing the degree of protection (or higher) included in Table 1 of IEC 61992-6
NOTE Metal-enclosed switchgear in which the main circuit components are individually embedded in solid insulating material can be considered as an alternative, provided that the conditions specified in IEC 60466 are met.
[IEC 61992-1, ed. 2.0 (2006-02)]
cubicle switchgear
switchgear, other than metal-clad and compartmented switchgear
NOTE This term applies to switchgear having a metal enclosure and having
– a number of compartments fewer than required for metal-clad or compartmented switchgear, or
– partitions having a degree of protection lower than those indicated in Table 1 of IEC 61992-6, or
– no partitions.
[IEC 61992-1, ed. 2.0 (2006-02)]FR
appareillage sous enveloppe métallique
ensemble d’appareillage avec une enveloppe métallique externe destinée à être mise à la terre, entièrement terminé, à l’exception des connexions extérieures
NOTE L’appareillage sous enveloppe métallique se subdivise en trois types:
– appareillage recouvert de métal;
– appareillage à compartiments (avec une ou plusieurs cloisons non métalliques);
– appareillage d’armoire.
[IEC 61992-1, ed. 2.0 (2006-02)]
appareillage recouvert de métal
appareillage sous enveloppe métallique dans lequel les éléments constitutifs sont disposés dans des compartiments séparés par des cloisons métalliques destinées à être mises à la terre
NOTE 1 Ce terme s’applique à l’appareillage sous enveloppe métallique avec des cloisons métalliques offrant le degré de protection de la CEI 61992-6 (ou un degré supérieur) et ayant des compartiments séparés au moins pour les éléments constitutifs suivants:
– chaque appareil principal de connexion;
– les éléments constitutifs connectés à une face de l'appareil principal de connexion, par exemple le circuit d’alimentation;
– les éléments constitutifs connectés à l’autre face de l'appareil principal de connexion, par exemple les jeux de barres; lorsqu’il y a plus d’un jeu de barres, chaque jeu est dans un compartiment séparé.
NOTE 2 L’appareillage sous enveloppe métallique qui possède des cloisons métalliques et qui répond à toutes les dispositions de la note 1 peut utiliser une barrière en volet isolant comme une partie d’une disposition de volet, dont la combinaison fournit un degré de protection inclus au Tableau 1 de la CEI 61992-6 (ou un degré supérieur) et satisfait aux exigences de la norme pour les cloisons et les volets en matériau isolant.
[IEC 61992-1, ed. 2.0 (2006-02)]
appareillage à compartiments (avec cloisons non métalliques)
appareillage sous enveloppe métallique dans lequel les éléments constitutifs sont disposés dans des compartiments séparés comme pour l’appareillage recouvert de métal, mais avec une ou plusieurs cloisons non métalliques fournissant le degré de protection du Tableau 1 de la CEI 61992-6 (ou un degré supérieur)
NOTE L’appareillage sous enveloppe métallique dans lequel les éléments constitutifs du circuit principal sont noyés individuellement dans un matériau isolant solide peut être considéré comme une alternative, si les conditions spécifiées dans la CEI 60466 sont satisfaites.
[IEC 61992-1, ed. 2.0 (2006-02)]
pareillage d’armoire
appareillage, autre que l’appareillage recouvert de métal ou à compartiments
NOTE Ce terme s’applique à l’appareillage ayant une enveloppe métallique et ayant:
– soit un nombre de compartiments inférieur à celui exigé pour les appareillages recouverts de métal ou à compartiments;
– soit des cloisons d’un degré de protection inférieur à ceux du Tableau 1 de la CEI 61992-6;
– soit pas de cloisons.
[IEC 61992-1, ed. 2.0 (2006-02)]
Комплектное распределительное устройство в металлической оболочке
Рис. ABBГОСТ 14693-90 - Устройства комплектные распределительные негерметизированные в металлической оболочке на напряжение до 10 кВ
Тематики
- комплектное распред. устройство (КРУ)
Синонимы
EN
- compartmented switchgear (with non-metallic partitions)
- cubicle switchgear
- MCSG
- MESG
- metal clad switch gear
- metal clad switchgear
- metal-enclosed switchgear
- metalclad switch gear
- metalclad switchgear
FR
Русско-французский словарь нормативно-технической терминологии > комплектное распределительное устройство в металлической оболочке
-
15 измеренное значение параметра
измеренное значение параметра
Значение параметра, установленное в результате его измерения определенным средством контроля.
[ ГОСТ 19919-74]EN
measured value
physical or electrical quantity, property or condition that is to be measured
NOTE 1 Measured values are usually monitored, but may be calculated from other values. They are also usually considered to be analogue values.
NOTE 2 The result of a sampling of an analogue magnitude of a particular quantity.
[IEC 61850-7-4]
measured value
estimate of the true value of a quantity, derived from the indicated value of a meter after applying all relevant correction factors
[IEC 60788, ed. 2.0 (2004-02)]
measured value
best estimate of the true value of a quantity, being derived from the indicated value of an instrument together with the application of all relevant correction factors and the calibration factor
Note 1 to entry: The measured value is sometimes also referred to as result of a measurement
[IEC 61674, ed. 2.0 (2012-11)]FR
valeur mesurée
meilleure estimation de la valeur vraie d'une grandeur, qui est déduite de la valeur indiquée par un instrument ainsi que de l'application de tous les facteurs de correction appropriés et du facteur d’étalonnage
Note 1 à l'article: La valeur mesurée est parfois également désignée par «résultat d’une mesure».
[IEC 61674, ed. 2.0 (2012-11)]Значение регулируемой величины, полученное в рассматриваемый момент времени на основании данных некоторого измерительного прибора называется ее измеренным значением.
[ http://infor.wallst.ru/5/ab3.htm]Тематики
- контроль автоматизир. тех. состояния авиац. техники
- электротехника, основные понятия
Обобщающие термины
- параметры контроля, их значения и определение
Синонимы
EN
FR
Русско-французский словарь нормативно-технической терминологии > измеренное значение параметра
-
16 обслуживание техническое
техническое обслуживание
Совокупность действий, выполняемых для сохранения или восстановления состояния изделия, в котором оно способно отвечать требованиям соответствующих технических условий и выполнять необходимые функции.
[ ГОСТ Р МЭК 60050-426-2006]
техническое обслуживание
Текущие действия, выполняемые для сохранения в полной мере работоспособного состояния установленного электрооборудования.
[ ГОСТ Р МЭК 60050-426-2006]
техническое обслуживание
Комплекс операций и/или организационных действий, направленных на поддержание объекта в состоянии или возвращение объекта в состояние, в котором он способен выполнять требуемую функцию.
[ОСТ 45.152-99 ]
обслуживание техническое
Комплекс работ для поддержания исправности или работоспособности машин и оборудования при их эксплуатации, хранении и транспортировании
[Терминологический словарь по строительству на 12 языках (ВНИИИС Госстроя СССР)]EN
maintenance
1. All action taken to retain materiel in or to restore it to a specified condition. It includes: inspection, testing, servicing, classification as to serviceability, repair, rebuilding, and reclamation.
2. All supply and repair action taken to keep a force in condition to carry out its mission.
3. The routine recurring work required to keep a facility (plant, building, structure, ground facility, utility system, or other real property) in such condition that it may be continuously utilized, at its original or designed capacity and efficiency, for its intended purpose.[Dictionary of Military and Associated Terms. US Department of Defense 2005]Тематики
- тех. обсл. и ремонт средств электросвязи
Синонимы
- ТО
EN
- backup
- concept maintenance
- engineering service
- machine servicing
- maintenance
- maintenance service
- maintenance support
- maintenance work
- maintenance works
- mechanical services
- servicing
- technical maintenance
DE
FR
Русско-французский словарь нормативно-технической терминологии > обслуживание техническое
17 отделять, отделение
отделять
Полностью отсоединять устройство или электрическую цепь от других устройств или электрических цепей.
[Перевод Интент]
отделять
изолировать
-
[IEV number 151-15-37]EN
isolate (1), verb
disconnect completely a device or an electric circuit from other devices or electric circuits
[IEV number 151-15-37]FR
isoler (2), verbe
déconnecter complètement un dispositif ou un circuit électrique d'autres dispositifs ou circuits électriques
[IEV number 151-15-37]461.1 В зависимости от предназначенной ему функции любое устройство, предназначенное для отделения, отключения или управления, должно соответствовать требованиям стандартов и технических условий на эти устройства.
461.2 В системах TNС нулевой рабочий проводник, совмещенный с защитным, отделять или отключать не следует. В системе TNS отделять или отключать рабочий нулевой проводник не требуется.
Во всех системах распределения электроэнергии отделять или отключать защитные проводники не допускается.
461.3 Мероприятия, приведенные в настоящем стандарте, не заменяют меры защиты, установленные в других стандартах на электроустановки зданий.
462 Отделение
462.1 В каждой цепи должна быть предусмотрена возможность отделения каждого проводника от питающих проводников, находящихся под напряжением, за исключением упомянутых в 461.2.
Допускается предусматривать отделение группы цепей общим устройством, если это позволяют условия эксплуатации.
[ ГОСТ Р 50571. 7-94 ( МЭК 364-4-46-81)]Параллельные тексты EN-RU
When the supply disconnecting device is one of the types specified in 5.3.2 a) to d) it shall fulfil all of the following requirements:
– isolate the electrical equipment from the supply and have one OFF (isolated) and one ON position marked with "O" and "I" …;
...
[IEC 60204-1-2006]Аппараты отключения электропитания, указанные в п. 5.3.2, в перечислениях а)...d), должны удовлетворять всем перечисленным ниже требованиям:
- отделять электрооборудование от источника питания и иметь одно положение ОТКЛЮЧЕНО (отделенное положение) и одно положение ВКЛЮЧЕНО, обозначенные символами «О» и «I» соответственно...;
...
[Перевод Интент]isolation
function intended to make dead for reasons of safety all or a discrete section of the electrical installation by separating the electrical installation or section from every source of electric energy
[IEV number 826-17-01]разъединение (функция)
Действие, направленное на отключение питания всей установки или ее отдельной части путем отделения этой установки или части ее от любого источника электрической энергии по соображениям безопасности.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]Compact CVS circuit breakers are suitable for Isolation as defined in EC standards 60947-2. The aim of isolation is to separate a circuit or apparatus from the remainder of a system which is energized in order the personnel may carry out work on the isolated part with complete safety.
[Schneider Electric]Автоматический выключатель CVS пригоден к разъединению - функции, определенной в европейском стандарте 60947-2. Целью разъединения является отделение цепей или аппаратов от части системы, остающейся под напряжением для обеспечения полной безопасности персонала, работающего на отделенной части системы.
[Перевод Интент]
Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > отделять, отделение
18 вспомогательная цепь (автоматического выключателя)
вспомогательная цепь (автоматического выключателя)
Совокупность токопроводящих частей1) автоматического выключателя, предназначенных для включения в цепь, кроме главной цепи и цепи управления автоматического выключателя
[ ГОСТ Р 50345-99( МЭК 60898-95)]EN
auxiliary circuit (of a circuit-breaker)
all the conductive parts of a circuit-breaker intended to be included in a circuit other than the main circuit and the control circuit of the circuit-breaker
[IEC 60898-1, ed. 1.0 (2002-01)]FR
circuit auxiliaire (d'un disjoncteur)
ensemble des parties conductrices d'un disjoncteur destinées à être insérées dans un circuit autre que le circuit principal et le circuit de commande du disjoncteur
[IEC 60898-1, ed. 1.0 (2002-01)]1) должно быть проводящих частей
[Интент]Тематики
EN
FR
Русско-французский словарь нормативно-технической терминологии > вспомогательная цепь (автоматического выключателя)
19 вспомогательная цепь НКУ
вспомогательная цепь НКУ
Все токоведущие части НКУ, включенные в цепь, предназначенную для управления, измерения, сигнализации, регулирования, обработки и передачи данных и т. д. и не являющуюся главной цепью.
Примечание — Цепи управления и вспомогательные цепи коммутационных аппаратов относятся к вспомогательным цепям.
(МЭС 441-13-03, с изменением)
[ ГОСТ Р 51321. 1-2000 ( МЭК 60439-1-92)]
вспомогательная цепь НКУ
Совокупность токоведущих частей комплекта, входящих в цепь (кроме главной цепи), предназначенную для управления, измерения, сигнализации, регулирования и обработки данных и т.д.
Примечание — Вспомогательные цепи комплекта включают цепи управления и вспомогательные цепи коммутационных устройств.
[ ГОСТ Р МЭК 61439.1-2013]EN
auxiliary circuit (of an assembly)
all the conductive parts of an assembly of switchgear and controlgear included in a circuit (other than the main circuit) intended to control, measure, signal and regulate
NOTE – The auxiliary circuits of an assembly include the control and auxiliary circuits of the switching devices.
[IEV number 441-13-03]FR
circuit auxiliaire (d'un ensemble)
toutes les pièces conductrices d'un ensemble insérées dans un circuit, autre que le circuit principal, destinées à la commande, la mesure, la signalisation et la régulation
NOTE – Les circuits auxiliaires d'un ensemble comprennent les circuits de commande et les circuits auxiliaires des appareils de connexion.
[IEV number 441-13-03]Тематики
- НКУ (шкафы, пульты,...)
Классификация
>>>Синонимы
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > вспомогательная цепь НКУ
20 вспомогательная цепь коммутационного аппарата
вспомогательная цепь коммутационного аппарата
Все токоведущие части коммутационного аппарата, предназначенные для включения в цепь, кроме главной цепи и цепи управления аппарата.
МЭК 60050(441-15-04).
Примечание. Некоторые вспомогательные цепи выполняют дополнительные функции (сигнализация, блокировка и т. д.) и поэтому они могут входить в состав цепи управления другого коммутационного аппарата.
[ ГОСТ Р 50030. 1-2000 ( МЭК 60947-1-99)]EN
auxiliary circuit (of a switching device)
all the conductive parts of a switching device which are intended to be included in a circuit other than the main circuit and the control circuits of the device
NOTE – Some auxiliary circuits fulfil supplementary functions such as signalling, interlocking, etc., and, as such, they may be part of the control circuit of another switching device.
[IEV number 441-15-04]FR
circuit auxiliaire (d'un appareil de connexion)
ensemble de pièces conductrices d'un appareil de connexion destinées à être insérées dans un circuit autre que le circuit principal et les circuits de commande de l'appareil
NOTE – Certains circuits auxiliaires remplissent des fonctions supplémentaires telles que la signalisation, le verrouillage, etc., et, à ce titre, ils peuvent faire partie du circuit de commande d'un autre appareil de connexion.
[IEV number 441-15-04]Тематики
- аппарат, изделие, устройство...
EN
DE
FR
Русско-французский словарь нормативно-технической терминологии > вспомогательная цепь коммутационного аппарата
СтраницыСм. также в других словарях:
all/other things being equal — see ↑thing • • • Main Entry: ↑equal all/other things being equal formal used to say what should happen or be true if two situations, products, etc., are different in a specified way but not in other ways All things being equal, a person with a… … Useful english dictionary
all other things being equal — (all) other things being equal if everything happens as you expect it to happen. All things being equal, I should be home by Thursday … New idioms dictionary
all other cases not expressly provided for — A common provision in limitation statutes which is usually deemed comprehensive of every action or proceeding in a court of justice wherein a contested question may arise, but sometimes limited to actions as distinguished from special proceedings … Ballentine's law dictionary
All I Ever Wanted (album) — All I Ever Wanted Studio album by Kelly Clarkson Released … Wikipedia
other things being equal — Associated circumstances being unchanged • • • Main Entry: ↑other * * * all/other/things being equal phrase if things stay as expected, or if there are no special facts to consider All things being equal, we should get there by the evening. Othe … Useful english dictionary
All or nothing (armor) — All or nothing is a method of armoring battleships, originally developed by the US Navy in the first decade of the 20th century. The characteristic of the system was the avoidance of light or moderate thicknesses of armor; armor was used in the… … Wikipedia
All-Star Final Vote — 2007 National League All Star Final Vote winner Chris Young warming up in the Wrigley Field bullpen with a four seam fastball Awarded for … Wikipedia
all things being equal — all/other/things being equal phrase if things stay as expected, or if there are no special facts to consider All things being equal, we should get there by the evening. Other things being equal, the job would be given to a woman. Thesaurus: words … Useful english dictionary
All Saints High School, Hyderabad — All Saints High School is a Catholic school in Hyderabad, India, offering an outstanding education for children from pre Kindergarten to Tenth Standard (matriculation). It was founded in the year 1855 and is run by the [http://www.montfort.net… … Wikipedia
All Star Baseball — is one of the two most popular baseball board games of the last sixty years, and has been honored as one of the fifty most influential American board games of all time. It was manufactured by Cadaco Ellis and designed by baseball player Ethan… … Wikipedia
all right vs alright — All right has multiple meanings. It can mean ok, acceptable, unhurt. The single word spelling alright has never been accepted as standard. However in a search on Google you ll get around 68,700,000 hits for alright and 163,000,000 for all… … English dictionary of common mistakes and confusing words
Перевод: с русского на французский
с французского на русский- С французского на:
- Русский
- С русского на:
- Все языки
- Английский
- Итальянский
- Немецкий
- Французский